Hi Everyone
Where and how do I install and setup cccam for my solo2 vu box? I have installed Vix image backup by ten below, have Ethernet cable connected.
Do I have to setup a server first?
Thanks in advance..
Hi Everyone
Where and how do I install and setup cccam for my solo2 vu box? I have installed Vix image backup by ten below, have Ethernet cable connected.
Do I have to setup a server first?
Thanks in advance..
CCcam will already be installed on the Vix image backup by ten below, Press blue button > Softcam Manager > Start CCcam with the Green button and Enable Startup Blue button..
Take a look at this guide if you don`t understand how to use CCcam here --> Getting Started - Flines & Clines For Beginners..
Still cannot find it, on the backup image by Ten Below it seems to say that you have to install it after you flash the image.
I don't think I have my router setup to accept ftp transfers yet, this part is hard. Does anyone anyone know of a guide on how to set up a solo2 box with router/port forwarding etc.... .????
It all depends on what router you have just with it plugged in you should be able to go to menu/information/network and you will see what ip address the box has , the post with the backup tells yo the passwords ,and if you look for vu+ toolbox you will be able to connect via cline manager , the port forwarding you will need to google your model and youll find that information
Hi Steviejo,
When you say google model, do you mean the router ?
Hi Steviejo,
When you say google model, do you mean the router ?
yes they are all slightly different
Still cannot find it, on the backup image by Ten Below it seems to say that you have to install it after you flash the image.
I don't think I have my router setup to accept ftp transfers yet, this part is hard. Does anyone anyone know of a guide on how to set up a solo2 box with router/port forwarding etc.... .????
CCcam the emulator is installed on the image but you have to add your C line to the CCcam.cfg which is in folder /etc/..
Are you looking to setup and share your card or are you only using a share ?
You don`t need to open ports in the router if you are only a client ( using a C line ), if you are looking to share your card then you will need to open ports so others can connect to your server..
No other configuration is needed to gain access to your receiver with FTP inside your own network.. Try using this FTP tool here --> DCC-E2 Dreambox Control Center..
Which router ( make & model ) do you have so we can link you a port forwarding guide ?
I would like to set it up so I can do both, my router is a Netgear DG834G wireless router with four Ethernet ports, thanks.
Use this guide here --> Port Forwarding the Netgear DG834G Router for 1AVStreamer..
Open the SERVER LISTEN PORT: in the CCcam.cfg file, the default port is 12000, but choose something random and less obvious for hackers..
Use this site to check if the ports have been opened properly in the router here --> http://www.canyouseeme.org/
Have now used DCC to connect to my vu box, thanks for all the help so far, feel like I am now gettimg somewhwere,
story so far,
Using the ftp panel I was able to open the /etc/ folder, but found no cccam or Cccam.cfg files/folders, do I have to install Cccam and the Cccam.cfg ??
If Tspanel is installed in the back up just download a cam pack from there,then install
Press Blue button then Softcam Manager, you should see CCcam in this list, start CCcam and enable at startup..
If you don`t have a CCcam.cfg file in /etc/ then use this here --> http://linuxsat-support.com/cc…cam-cfg-file-newbies.html..
Tell us which card are you trying to share so we can link you the emulator and configs needed..
Don’t have an account yet? Register yourself now and be a part of our community!