hi
i have a xtrend et6000 running cccam,it just open jsc i install cccam info and in share view 11 available and 7 provider (***,mtv,sct....)
i change different file perio and other but nothing happen im using cccam 2.3.0
can someone tell me what i do?
thnks
cccam problem
-
- Various Support
- pnkpanther
- Thread is marked as Resolved.
There are 9 replies in this Thread which was already clicked 1,722 times. The last Post () by canthackit.
-
-
Post your introduction and follow the forum rules before requesting support http://linuxsat-support.com/introductions/
-
Post your introduction and follow the forum rules before requesting support Forum Gateway - Powered by DnP Firewall
ok
can someone help me
plz -
How are you receiving your services? Just because it is showing in CCcam info it does not mean it will clear. If it is a poor quality server then you may find JSC works because it does not make many server requests as other services, where other services may need to send requests more frequently to the server to clear.
-
How are you receiving your services? Just because it is showing in CCcam info it does not mean it will clear. If it is a poor quality server then you may find JSC works because it does not make many server requests as other services, where other services may need to send requests more frequently to the server to clear.
i dont know but Previously worked fine
thanks -
i dont know but Previously worked fine
thanks
how can you not know how you are receiving your services?:beated: -
how can you not know how you are receiving your services?:beated:
im in Netherlands and im receiving from XXXXXXXXXXXXX
did u mean this?
i attached sample my cfg file maybe not correct
SERVER LISTEN PORT : 13000
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME :root
WEBINFO PASSWORD :dreambox
TELNETINFO USERNAME :root
TELNETINFO PASSWORD :dreambox
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 16001
ZAP OSD TIME :0
OSD USERNAME :root
OSD PASSWORD :dreambox
OSD PORT :80
SHOW TIMING : yes
DEBUG : no
NEWCAMD CONF : no
#DISABLE EMM : yes
#EXTRA EMM LEVEL : yes
SHOW EXTENEDED CLIENT INFO : yes
MINI OSD : no
#MINIMUM DOWNHOPS: 1
CHANNELINFO FILE : /var/etc/CCcam.channelinfo
PROVIDERINFO FILE : /var/etc/CCcam.providers
CAID PRIO FILE : /var/etc/CCcam.prio
LOG WARNINGS : /tmp/warnings.txt
SOFTKEY FILE : /var/keys/SoftCam.Key
AUTOROLL FILE : /var/keys/AutoRoll.Key
#STATIC CW FILE : /var/keys/constant.cw
#BOXKEY:
#SMARTCARD CLOCK FREQUENCY: /dev/sci0 6800000 -
if that's your CCcam.conf file
then when loading the prio file you've probably overwritten your orginal CCcam.config file, if you've made a back up copy it over.
if not you need to reconfigure your config file.
regards: canthackit
-
Display More
if that's your CCcam.conf file
then when loading the prio file you've probably overwritten your orginal CCcam.config file, if you've made a back up copy it over.
if not you need to reconfigure your config file.
regards: canthackit
i havent made a back up i edit cccam.cfg several times and i use different perio file and other
Tell me if there's a way
best kind regards -
if it's a server you need to add your F lines
if it's your client you need to add your C lines.
if you use it for both you need to add both, that is C and F lines.if your not sure how to do the above check out the link below.
http://linuxsat-support.com/ca…nes-clines-beginners.html
hope this helps.
regards: canthackit
CCcam Support Forum
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
