Trying to load Backup Image 2.0.8 but can't get it to load and replace Blackhole 2.0.5 .I have the image on my memory stick in a folder called vuplus and when I open that folder I have solo2 and in that I have the 4 files . I turn off the solo2 with switch on the back and put my memory stick in the front usb slot .Now the problems start.The first few times I tried to load it I got the prompt to press the power button and it then went through the motions of loading the image but after rebooting I still have Image 2.0.5 when I go to menu>info>about .Now when I try to load the image it will not prompt me to press the power button .I also tried OpenVIX 748 UK Ready VU+Solo2 Backup By Ten Below and still same problem.THE box is STILL working on the 2.0.5 image even after all the attempts to remove it but I have lost MANU tv.What is happening ?
Loading latestBlackhole Backup image by Ten Below
- limerick
- Thread is marked as Resolved.
-
-
try loading 2.0.8 image first not the backup image,dont think you can backup before you do.
-
just put the solo2 file on the usb stick and you should be good to go it happened to me mate
-
I would try a different usb stick.. If you don`t have another one use this tool ## USB Format Tool ##.
Copy & paste the vuplus.zip file to the usb > Right click on this file and select extract here with winrar > Delete the vuplus.zip file.
Now try to flash the image..
-
I'm having the same problem with this particular backup. I have installed most (if not all) of Ten Below's previous BH backups with no problem. Using the same USB stick I have the appearance of loading, but still on 2.0.7.3. Done it a number of times, used two different USB sticks - one formatted with the HP utility. Still the same outcome!!!
-
Quote
FPGA update in solo2(done automatically in the first bootup after installation)
It`s possible the backup doesn`t include this necessary update.. Look for FPGA Update in your plugin menu or flash the base image first, then the backup..
-
FPGA is in the "Firmware Upgrade" plugin. What do I do with it?
-
FPGA is in the "Firmware Upgrade" plugin. What do I do with it?
Green button > Firmware Upgrade > Green button / Upgrade > Blue button / Download..
-
Green button > Firmware Upgrade > Green button / Upgrade > Blue button / Download..
Done that, and get a message "Firmware does not exist"!!
Not super urgent, BH2.0.7.3 working well, so I will wait until this is resolved.
Thanks.
-
I have tried 2.0.7 backup image on another memory stick but it still wont even attempt to load and also FPGA does not exist on the 2.0.5 image that's on the box.Should I try and load 2.0.8 image first and then the backup one or leave it alone in case I finish up with nothing
-
Try loading ## Black Hole Vu+ Solo2 v.2.0.8 ##, then try the backup..
-
It wont even attempt to load v2.0.8. not getting the prompt to press the power button on the front panel
-
latest image worked no problem for me infact I look foreward to them being released, thanks tenbelow for the effort
-
I have never had a problem with Ten Below's BH backups - until now. It's clearly not this backup since no other backup will load either - and all have loaded previously. Using the same USB sticks the box goes through all the correct stages when flashing, but ends up still on BH2.0.7.3 no matter what BH backup image I am trying to load. It looks like either something set in the box (which rejects the flash) or the box is having difficulty with USB sticks it previously was very happy with. Not sure whether a "Factory Reset" is available and whether that would help? Anyone else in the same boat?
-
I have never had a problem with Ten Below's BH backups - until now. It's clearly not this backup since no other backup will load either - and all have loaded previously. Using the same USB sticks the box goes through all the correct stages when flashing, but ends up still on BH2.0.7.3 no matter what BH backup image I am trying to load. It looks like either something set in the box (which rejects the flash) or the box is having difficulty with USB sticks it previously was very happy with. Not sure whether a "Factory Reset" is available and whether that would help? Anyone else in the same boat?
Did you at any point make a backup of your own image?
Check your storage devices for any vuplus folders, it sounds as if you are flashing a backup of your currently installed image. -
Yes, I always take a backup before starting - but it is saved on the USB stick in the back of the machine. The new image is always placed in the front USB slot. Is that not correct?
-
Yes, I always take a backup before starting - but it is saved on the USB stick in the back of the machine. The new image is always placed in the front USB slot. Is that not correct?
No the solo2 can flash from anywhere including hdd, delete the backup then try flashing again. -
Only have the USB with the new image inserted.. Remove any other usb devices while trying to flash an image..
-
Will try that - this evening! The kids will kill me if I tamper with the box interfering with their football viewing!!
Thanks, will let you know.
-
When I go into Media player there is a file vuplus and when opened solo2 is inside ,could this be the reason Ican't put on a new image .I am trying to delete the file ,can someone tell me how to delete it please and is this my problem
VU+ SOLO 2 PVR Ready Linux Enigma2 Receiver Full HD 1080p
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!