Hi everybody
I try many way to config my DM500s to read the nagra3 card use (Oscam, newcs, CCcam...) but the end I only see caid (1802), no provider and no picture of course. Does any body use to config nagra3 card, pls help me or send me a backup image for DM500s. I really thank.
Nagra 3 in Vietnam
-
- Various Support
- dvb_s2
- Thread is marked as Resolved.
There are 14 replies in this Thread which was already clicked 7,685 times. The last Post () by cuongdaiphuc.
-
-
who is your provider in vietnam ?
new2
-
Provider in Viet Nam use Nagra3 card is VSTV Kplus
-
hi
program in oscam.server like this : -
[reader]
label = VSTV
enable = 1
detect = cd
protocol = internal
device = /dev/sci0
caid = 1820
ident = 1820:000000
group = 1
emmcache = 1,1,2
mhz = 357
cardmhz = 357
blockemm-unknown = 1new2
-
Dear Newtolinux, I try your code and it is still no picture
Here is Oscam log1970/01/01 2:00:19 31825B50 r reader thread started (thread=31825B50, label=vstv, device=/dev/sci0, detect=cd, mhz=357, cardmhz=357)
1970/01/01 2:00:19 31825B50 r vstv card detected
1970/01/01 2:00:20 31825B50 r Extra delay for PPC box between reset and IO_Serial_Read for the ATR
1970/01/01 2:00:21 31825B50 r ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
1970/01/01 2:00:22 31825B50 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
1970/01/01 2:00:23 31825B50 r detect native nagra card
1970/01/01 2:00:23 31825B50 r -----------------------------------------
1970/01/01 2:00:23 31825B50 r |id |tier |valid from |valid to |
1970/01/01 2:00:23 31825B50 r +----+--------+------------+------------+
1970/01/01 2:00:23 31825B50 r |AA61|000E |2020/12/31 |2011/08/05 |
1970/01/01 2:00:23 31825B50 r |AA61|0017 |2020/12/31 |2011/08/05 |
1970/01/01 2:00:23 31825B50 r |AA61|000B |2020/12/31 |2011/08/05 |
1970/01/01 2:00:23 31825B50 r -----------------------------------------
1970/01/01 2:00:23 31825B50 r Negotiate sessionkey was not successfull! Please check rsa key and boxkey
1970/01/01 2:00:23 31825B50 r card system not supported
1970/01/01 2:00:23 31825B50 r Normal mode failed, reverting to Deprecated Mode
1970/01/01 2:00:24 31825B50 r Extra delay for PPC box between reset and IO_Serial_Read for the ATR
1970/01/01 2:00:25 31825B50 r ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
1970/01/01 2:00:26 31825B50 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
1970/01/01 2:00:28 31825B50 r detect native nagra card
2011/06/10 5:35:23 31825B50 r card system not supported
2011/06/10 5:35:23 31825B50 r card initializing error
2011/06/10 5:35:23 30016270 s init for all local cards done
2011/06/10 5:35:24 32025B50 c client connected to 43000 port
2011/06/10 5:35:24 32025B50 c encrypted newcamd:43000-client 127.0.0.1 granted (dm500, au=on (1 reader))
2011/06/10 5:35:24 32025B50 c user dm500 authenticated successfully (CCcam)
2011/06/10 5:35:24 32025B50 c AU disabled for user dm500Please tell me what reason and what can I do with this card.
Many thanks -
-
Yes, that is my problem, How can i do to know rsa and boxkey. Pls help me. Thank alot
-
Today, I find out my nagra3 card has ROM 180 inside. and the problem now is what Cam (Newsc, Oscam....) I use to config this card for my DM500. Please help me. Thank to all.
-
I have backup my image Dm500S
with card n3
i find again my data at home -
We are doing some system testing in Europe, a few more issues will be sent to the email to
jonhterry see if that helps. Thanks!and this is my:nag3 card on Dreambox
Opening sci... Done
Detecting card... Card present
root@dm500 ~ # Resetting card... Done
Identifying card type...
Historical bytes: D N A S P 1 4 2 R e v G 0 2
44 4E 41 53 50 31 34 32 20 52 65 76 47 30 32
Card type: Nagra
ROM Revision: 142
EEPROM Revision: RevG02
Configuring sci...
SCI | f: 3574595 | T: 1 | ETU: 32 | EGT: 1 | CWT: 25 | BWT: 89291 | WWT: 0
Slot custom parameters:
des_key: 0102030405060708091011121314
box_key: ################
dt06_key_0d:
cam_n: ######################## ...
Long parameter, first 32 characters shown, 128 total.
secondary_key:
rsa_key:
Card start-up initialization...
Using Plain CAM N session negotiation method:
Setting Field Size: Done
Retrieving IRD serial number: ########
Retrieving CAM serial number: ########
Retrieving System IDs: 5F01,5F02
Retrieving CAM challenge data: Done
Performing Session Key Negotiation: Successful
Starting card worker thread... Done
Starting protocol server on port 10000 [newcamd protocol]
Logical Slot 'Lower' READY!read the card ok, now a few steps to help mgcamd:
[mg0] stoping camd..
/dev/dvb/card0/ca0 error 16: Device or resource busy
/dev/dvb/card0/ca0 error 16: Device or resource busy
got 52 cmd 9F
[mg0] namespace FFFF0000 t-id 38 on-id 601
[mg0] descramble on 1, source 0
[mg0] service 25A index 0 pmt pid 21 (19)
ECM: CaID: 0x1802 -> CaPID: 0x0692 ProvID: 000000
[mg0] network can't decode
[mg0] pid 0x0692 failed to decode.
[mgcamd] emm started
*EMM: CaID: 0x1800 -> CaPID: 0x0080 ProvID: 000000
*EMM: CaID: 0x1801 -> CaPID: 0x0081 ProvID: 000000
*EMM: CaID: 0x1802 -> CaPID: 0x0082 ProvID: 000000
DISCONNECT **** Client disconnected...
User: 'dummy' | Current clients: 0
[newcamd] 127.0.0.1:10000: problem, will try to reconnect
[newcamd] Connecting to 127.0.0.1:10000...
[newcamd] Login to 127.0.0.1:10000 as dummy accepted (31ms)
CONNECT **** Processing incoming connection...
User 'dummy' authenticated [Client: unknown] | Clients: 1
[newcamd] Card data from 127.0.0.1:10000 (34ms):
Userid 0 caid 1802 providers 2
Idents: 005F01 005F02
DATA **** Processing card data request...
Username: dummy | Logical slot: 'Lower' | Card data sent successfully.
DISCONNECT **** Client disconnected...
User: 'dummy' | Current clients: 0
[newcamd] 127.0.0.1:10000: problem, will try to reconnect
[newcamd] Connecting to 127.0.0.1:10000...
[newcamd] Login to 127.0.0.1:10000 as dummy accepted (31ms)
CONNECT **** Processing incoming connection...
User 'dummy' authenticated [Client: unknown] | Clients: 1
[newcamd] Card data from 127.0.0.1:10000 (34ms):
Userid 0 caid 1802 providers 2
Idents: 005F01 005F02
DATA **** ] Processing card data request...
Username: dummy | Logical slot: 'Lower' | Card data sent successfully.Please help me find the place I missed???
-
and this is my:nag3 card on Dreambox
Opening sci... Done
Detecting card... Card present
root@dm500 ~ # Resetting card... Done
Identifying card type...
Historical bytes: D N A S P 1 4 2 R e v G 0 2
44 4E 41 53 50 31 34 32 20 52 65 76 47 30 32
Card type: Nagra
ROM Revision: 142
EEPROM Revision: RevG02
Configuring sci...
SCI | f: 3574595 | T: 1 | ETU: 32 | EGT: 1 | CWT: 25 | BWT: 89291 | WWT: 0
Slot custom parameters:
des_key: 0102030405060708091011121314
box_key: ################
dt06_key_0d:
cam_n: ######################## ...
Long parameter, first 32 characters shown, 128 total.
secondary_key:
rsa_key:
Card start-up initialization...
Using Plain CAM N session negotiation method:
Setting Field Size: Done
Retrieving IRD serial number: ########
Retrieving CAM serial number: ########
Retrieving System IDs: 5F01,5F02
Retrieving CAM challenge data: Done
Performing Session Key Negotiation: Successful
Starting card worker thread... Done
Starting protocol server on port 10000 [newcamd protocol]
Logical Slot 'Lower' READY! -
Cái này hay đấy anh Huy à :57:
-
and this is my:nag3 card on Dreambox
Opening sci... Done
Detecting card... Card present
root@dm500 ~ # Resetting card... Done
Identifying card type...
Historical bytes: D N A S P 1 4 2 R e v G 0 2
44 4E 41 53 50 31 34 32 20 52 65 76 47 30 32
Card type: Nagra
ROM Revision: 142
EEPROM Revision: RevG02
Configuring sci...
SCI | f: 3574595 | T: 1 | ETU: 32 | EGT: 1 | CWT: 25 | BWT: 89291 | WWT: 0
Slot custom parameters:
des_key: 0102030405060708091011121314
box_key: ################
dt06_key_0d:
cam_n: ######################## ...
Long parameter, first 32 characters shown, 128 total.
secondary_key:
rsa_key:
Card start-up initialization...
Using Plain CAM N session negotiation method:
Setting Field Size: Done
Retrieving IRD serial number: ########
Retrieving CAM serial number: ########
Retrieving System IDs: 5F01,5F02
Retrieving CAM challenge data: Done
Performing Session Key Negotiation: Successful
Starting card worker thread... Done
Starting protocol server on port 10000 [newcamd protocol]
Logical Slot 'Lower' READY!jonh what are you use cam read card?
I have original card and box but i can not find rsakey and boxkey.
boxkey = box S/N ?
rsakey = card S/N ?
I have box and card S/N (12 digit) how to converse to Hex? -
hello all
i got problem setup nagra3 indonesian new paytv called BIGTV
its use ROM = DNASP190, REV MerQ25
on oscam its shown
Negotiate sessionkey was not successfull! Please check rsa key and boxkey
can you help me?
-
Hepl me!
[reader]
label = VSTV
enable = 1
detect = cd
protocol = internal
device = /dev/sci0
caid = 1820
ident = 1820:000000
group = 1
emmcache = 1,1,2
mhz = 357
cardmhz = 357
blockemm-unknown = 1
CCcam Support Forum
Configs, discussion, downloads and guides for CCcam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!