Nagra 3 in Vietnam

There are 14 replies in this Thread which was already clicked 7,636 times. The last Post () by cuongdaiphuc.

    Hi everybody
    I try many way to config my DM500s to read the nagra3 card use (Oscam, newcs, CCcam...) but the end I only see caid (1802), no provider and no picture of course. Does any body use to config nagra3 card, pls help me or send me a backup image for DM500s. I really thank.

    who is your provider in vietnam ?


    new2

    Dont forget to hit the thanks button!!!!!!!!!!!!!



    :41_002:



    Some articles may discuss topics that are illegal, so this information is provided for educational purposes only, your use of the content, downloads and files, or any part thereof, is made solely at your own risk and responsibility. Viewing Pay TV without a valid subscription is illegal. !! Linuxsat-Support.com cannot be held responsible for the content of any information stored or posted on this forum.

    hi


    program in oscam.server like this : -


    [reader]
    label = VSTV
    enable = 1
    detect = cd
    protocol = internal
    device = /dev/sci0
    caid = 1820
    ident = 1820:000000
    group = 1
    emmcache = 1,1,2
    mhz = 357
    cardmhz = 357
    blockemm-unknown = 1


    new2

    Dont forget to hit the thanks button!!!!!!!!!!!!!



    :41_002:



    Some articles may discuss topics that are illegal, so this information is provided for educational purposes only, your use of the content, downloads and files, or any part thereof, is made solely at your own risk and responsibility. Viewing Pay TV without a valid subscription is illegal. !! Linuxsat-Support.com cannot be held responsible for the content of any information stored or posted on this forum.

    Dear Newtolinux, I try your code and it is still no picture
    Here is Oscam log



    1970/01/01 2:00:19 31825B50 r reader thread started (thread=31825B50, label=vstv, device=/dev/sci0, detect=cd, mhz=357, cardmhz=357)
    1970/01/01 2:00:19 31825B50 r vstv card detected
    1970/01/01 2:00:20 31825B50 r Extra delay for PPC box between reset and IO_Serial_Read for the ATR
    1970/01/01 2:00:21 31825B50 r ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
    1970/01/01 2:00:22 31825B50 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
    1970/01/01 2:00:23 31825B50 r detect native nagra card
    1970/01/01 2:00:23 31825B50 r -----------------------------------------
    1970/01/01 2:00:23 31825B50 r |id |tier |valid from |valid to |
    1970/01/01 2:00:23 31825B50 r +----+--------+------------+------------+
    1970/01/01 2:00:23 31825B50 r |AA61|000E |2020/12/31 |2011/08/05 |
    1970/01/01 2:00:23 31825B50 r |AA61|0017 |2020/12/31 |2011/08/05 |
    1970/01/01 2:00:23 31825B50 r |AA61|000B |2020/12/31 |2011/08/05 |
    1970/01/01 2:00:23 31825B50 r -----------------------------------------
    1970/01/01 2:00:23 31825B50 r Negotiate sessionkey was not successfull! Please check rsa key and boxkey
    1970/01/01 2:00:23 31825B50 r card system not supported
    1970/01/01 2:00:23 31825B50 r Normal mode failed, reverting to Deprecated Mode
    1970/01/01 2:00:24 31825B50 r Extra delay for PPC box between reset and IO_Serial_Read for the ATR
    1970/01/01 2:00:25 31825B50 r ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
    1970/01/01 2:00:26 31825B50 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
    1970/01/01 2:00:28 31825B50 r detect native nagra card
    2011/06/10 5:35:23 31825B50 r card system not supported
    2011/06/10 5:35:23 31825B50 r card initializing error
    2011/06/10 5:35:23 30016270 s init for all local cards done
    2011/06/10 5:35:24 32025B50 c client connected to 43000 port
    2011/06/10 5:35:24 32025B50 c encrypted newcamd:43000-client 127.0.0.1 granted (dm500, au=on (1 reader))
    2011/06/10 5:35:24 32025B50 c user dm500 authenticated successfully (CCcam)
    2011/06/10 5:35:24 32025B50 c AU disabled for user dm500



    Please tell me what reason and what can I do with this card.
    Many thanks

    Code
    Negotiate sessionkey was not successfull! [COLOR='#FF0000']Please check rsa key and boxkey[/COLOR]

    Today, I find out my nagra3 card has ROM 180 inside. and the problem now is what Cam (Newsc, Oscam....) I use to config this card for my DM500. Please help me. Thank to all.

    We are doing some system testing in Europe, a few more issues will be sent to the email to
    jonhterry see if that helps. Thanks!


    and this is my:nag3 card on Dreambox


    Opening sci... Done
    Detecting card... Card present
    root@dm500 ~ # Resetting card... Done
    Identifying card type...
    Historical bytes: D N A S P 1 4 2 R e v G 0 2
    44 4E 41 53 50 31 34 32 20 52 65 76 47 30 32
    Card type: Nagra
    ROM Revision: 142
    EEPROM Revision: RevG02
    Configuring sci...
    SCI | f: 3574595 | T: 1 | ETU: 32 | EGT: 1 | CWT: 25 | BWT: 89291 | WWT: 0
    Slot custom parameters:
    des_key: 0102030405060708091011121314
    box_key: ################
    dt06_key_0d:
    cam_n: ######################## ...
    Long parameter, first 32 characters shown, 128 total.
    secondary_key:
    rsa_key:
    Card start-up initialization...
    Using Plain CAM N session negotiation method:
    Setting Field Size: Done
    Retrieving IRD serial number: ########
    Retrieving CAM serial number: ########
    Retrieving System IDs: 5F01,5F02
    Retrieving CAM challenge data: Done
    Performing Session Key Negotiation: Successful
    Starting card worker thread... Done
    Starting protocol server on port 10000 [newcamd protocol]
    Logical Slot 'Lower' READY!



    read the card ok, now a few steps to help mgcamd:


    [mg0] stoping camd..
    /dev/dvb/card0/ca0 error 16: Device or resource busy
    /dev/dvb/card0/ca0 error 16: Device or resource busy
    got 52 cmd 9F
    [mg0] namespace FFFF0000 t-id 38 on-id 601
    [mg0] descramble on 1, source 0
    [mg0] service 25A index 0 pmt pid 21 (19)
    ECM: CaID: 0x1802 -> CaPID: 0x0692 ProvID: 000000
    [mg0] network can't decode
    [mg0] pid 0x0692 failed to decode.
    [mgcamd] emm started
    *EMM: CaID: 0x1800 -> CaPID: 0x0080 ProvID: 000000
    *EMM: CaID: 0x1801 -> CaPID: 0x0081 ProvID: 000000
    *EMM: CaID: 0x1802 -> CaPID: 0x0082 ProvID: 000000
    DISCONNECT **** Client disconnected...
    User: 'dummy' | Current clients: 0
    [newcamd] 127.0.0.1:10000: problem, will try to reconnect
    [newcamd] Connecting to 127.0.0.1:10000...
    [newcamd] Login to 127.0.0.1:10000 as dummy accepted (31ms)
    CONNECT **** Processing incoming connection...
    User 'dummy' authenticated [Client: unknown] | Clients: 1
    [newcamd] Card data from 127.0.0.1:10000 (34ms):
    Userid 0 caid 1802 providers 2
    Idents: 005F01 005F02
    DATA **** Processing card data request...
    Username: dummy | Logical slot: 'Lower' | Card data sent successfully.
    DISCONNECT **** Client disconnected...
    User: 'dummy' | Current clients: 0
    [newcamd] 127.0.0.1:10000: problem, will try to reconnect
    [newcamd] Connecting to 127.0.0.1:10000...
    [newcamd] Login to 127.0.0.1:10000 as dummy accepted (31ms)
    CONNECT **** Processing incoming connection...
    User 'dummy' authenticated [Client: unknown] | Clients: 1
    [newcamd] Card data from 127.0.0.1:10000 (34ms):
    Userid 0 caid 1802 providers 2
    Idents: 005F01 005F02
    DATA **** ] Processing card data request...
    Username: dummy | Logical slot: 'Lower' | Card data sent successfully.


    Please help me find the place I missed???

    and this is my:nag3 card on Dreambox


    Opening sci... Done
    Detecting card... Card present
    root@dm500 ~ # Resetting card... Done
    Identifying card type...
    Historical bytes: D N A S P 1 4 2 R e v G 0 2
    44 4E 41 53 50 31 34 32 20 52 65 76 47 30 32
    Card type: Nagra
    ROM Revision: 142
    EEPROM Revision: RevG02
    Configuring sci...
    SCI | f: 3574595 | T: 1 | ETU: 32 | EGT: 1 | CWT: 25 | BWT: 89291 | WWT: 0
    Slot custom parameters:
    des_key: 0102030405060708091011121314
    box_key: ################
    dt06_key_0d:
    cam_n: ######################## ...
    Long parameter, first 32 characters shown, 128 total.
    secondary_key:
    rsa_key:
    Card start-up initialization...
    Using Plain CAM N session negotiation method:
    Setting Field Size: Done
    Retrieving IRD serial number: ########
    Retrieving CAM serial number: ########
    Retrieving System IDs: 5F01,5F02
    Retrieving CAM challenge data: Done
    Performing Session Key Negotiation: Successful
    Starting card worker thread... Done
    Starting protocol server on port 10000 [newcamd protocol]
    Logical Slot 'Lower' READY!


    jonh what are you use cam read card?
    I have original card and box but i can not find rsakey and boxkey.
    boxkey = box S/N ?
    rsakey = card S/N ?
    I have box and card S/N (12 digit) how to converse to Hex?

    hello all


    i got problem setup nagra3 indonesian new paytv called BIGTV


    its use ROM = DNASP190, REV MerQ25


    on oscam its shown


    Negotiate sessionkey was not successfull! Please check rsa key and boxkey


    can you help me?

    Hepl me!

    [reader]

    label = VSTV

    enable = 1

    detect = cd

    protocol = internal

    device = /dev/sci0

    caid = 1820

    ident = 1820:000000

    group = 1

    emmcache = 1,1,2

    mhz = 357

    cardmhz = 357

    blockemm-unknown = 1

CCcam Support Forum

Configs, discussion, downloads and guides for CCcam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login