Using a valid (paid subscripton) card with Dreambox 800se v2

There are 47 replies in this Thread which was already clicked 5,501 times. The last Post () by christian977.

    Hi again Guys,
    I have come a hell of a long way over the past couple of weeks, but i still can not get picture on the DB I have found the "streamboard tv" site and see a the card details there. i have tried numerous configs, but it seems no matter what config, or what oscam i use i always have the webif saying i have no card entitlements?? But the card works fine in the old decoder??
    Any idea's as to why oscam can not see card entitlements?? which settings would oscam used to verify the card? My log says that the card it detected? does the load balancer have anything to do with this?
    Thanks in advance.
    Christian

    • Official Post

    Try these changes in oscam..



    If the above fails try using CCcam 2.3.0 with the attached CCcam.cfg..


    CCcam WebInfo can be accessed in your browser http://ip.address.of.dm800:16001

    Code
    WEBINFO USERNAME :root
WEBINFO PASSWORD :dreambox
WEBINFO LISTEN PORT : 16001

    YAY!!!!!Thanks to this excellent site i have got the Oscam provided by MG reading the card!!!!! There was one item in the server that i changed and it worked. cardmhz = 2700
    What an education these dreamboxes have been so far!! tommorrow i will work out how to share to the other two with CCcam.
    Thanks MG and Rami!!!!:20_003:

    good, i am happy for you ,


    so is runing oscam with dvapi


    the best is n line in your to oder box ,


    go to user oscam ,copy wats you have and past 2 times with separation , change user and passwd to 2 differents, and groupe if dvapi is groupe 1 put groupe 2


    in your oscam configuration if you have only groupe 1 add 2 loock like this 1,2


    now in other box in cccam cfg delette alls


    and put this



    N: ip dor your dm master port you have in newcam user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 if ccam 213 add 256


    EXP.....N: 192.xxx.x.xx 12000 rtvi rtvi 01 02 03 04 05 06 07 08 09 10 11 12 13 14 box1


    N: 192.xxx.x.xx 12000 romeo romeo 01 02 03 04 05 06 07 08 09 10 11 12 13 14 box2


    remember if you runing cccam 213 add 256 afther 14 14 256



    you have to go in your router and open the port forwarding for your dm master


    ip your dm and the port 12000


    alls details ip port user and pass you have to put yours.



    hope my english is ok and you undesthud alls . good loock

    Hi MG, Thanks again, with out you and ramis help i had no chance...


    I am now trying to get the share working. I would like to do cccam like you have said. do i have to create a new ipk with my current oscam and cccam or is it jsut in the configs??? i have tried what is in linuxsat-support.com/showthread/.php/t=6057 but it brings up a line in my oscam log saying x.x.x.x detected and disconnected no 'accountname' account?" (sometihng like that...)


    I believe what got the box reading the card was the mhz or cardmhz setting. Anyways here is the configs that worked for me with my dm800sev2 using oscam r9792 to read my intertv card to see RTVI package......


    oscam.conf


    [global]
    logfile = var/log/oscam.log
    nice = -1
    preferlocalcards = 1


    [cache]


    [cccam]
    port = 12000
    serverip = xxx.xx.xx.xxx
    nodeid = xxxxxxxxxxxxxxxx
    version = 2.1.3
    reshare = 1



    [dvbapi]
    enabled = 1
    au = 1
    user = linuxsatsupport
    boxtype = dreambox


    [webif]
    httpport = 8888
    httprefresh = 10
    httpallowed = xxx.xx.1.1-255.255.255.255



    oscam.dvbapi


    P: 0500:FFF780
    oscam.server


    [reader]
    label = INTER_TV
    protocol = internal
    device = /dev/sci0
    caid = 0500
    detect = cd
    mhz = 0
    cardmhz = 2700
    ident = 0500:042300,024B00,FFF780
    group = 1


    oscam.user


    [account]
    user = linuxsatsupport
    description = dvbapi
    group = 1
    caid = 0500
    keepalive = 1
    au = 1



    Now off to read more on sharing....
    Thanks
    Christian

    • Official Post

    Make these changes on the server:


    Setup an [account] in oscam.user for each client/dreambox like so;


    CCcam protocol is already active in oscam.conf;

    Code
    [cccam]
port = 12000
serverip = xxx.xx.xx.xxx
nodeid = xxxxxxxxxxxxxxxx
version = 2.1.3
reshare = 1


    You now have three C lines configured, one for each dreambox. (change 192.168.1.97 to the ip address of the server)


    Code
    C: [COLOR='#FF0000']192.168.1.97[/COLOR] 12000 dreambox1 password1
C: [COLOR='#FF0000']192.168.1.97[/COLOR] 12000 dreambox2 password2
C: [COLOR='#FF0000']192.168.1.97[/COLOR] 12000 dreambox3 password3


    Make these changes on each client dreambox:


    Install CCcam 2.3.0..


    Copy and paste the above C line into the attached CCcam.cfg > FTP CCcam.cfg to the /etc folder > Activate CCcam in the image menu..


    Let us know how you get on buddy..

    Hi M.G,
    Once again, thank you!! I have the three boxes working, and we would like to get more....
    Thanks for all of you help this site proved very very very helpful and very informative.
    Christian

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login