I can not get my DM7020HD work with oscam!
I have tested several versions of oscam but the result is always the same = zero.
With the same oscam files on my ET9000, my TNTSAT and SmartHD+ cards work without any problem.
In both, my ET9000 and in my DM7020HD I'm using OpenPli4.0.
Any help?
DM7020 HD and oscam
-
- General OSCam
- rcc_pt
- Closed
- Thread is marked as Resolved.
-
-
Try the attached file, just add your own configs to it buddy..
-
I've tried with my own configs and and the result was the same: black screen.
I do not understand, in my ET9000 is working well.
In 7020HD only cccam works well!:confuse::sad: -
Try this binary, rename the oscam file to whatever your existing binary is already named as... chmod it to 755 and restart oscam
-
I give up, since a few days I have been trying without success.
Just do not understand is why the problem on Dreambox? -
Well you give up easy then dont ya, you are also not explaining the problem very well (zero) i take it you mean no webif access or oscam start?
-
The problems are no ecm info, no picture, no signal of cards detection, nothing at all.
-
The problems are no ecm info, no picture, no signal of cards detection, nothing at all.
I can sense you are getting a tad frustrated? you are best to leave that at the door before asking for help because you will be able to explain the issue more calmly with an end result of getting the help you need !
Webif? you have not mentioned this above?
Where are your config files located on this dreambox?
-
I do not know about the Webif, I do not use the Webif.
My config files, in Dreambox, are located in "etc/tuxbox/config/oscam".
In my ET9000 the configs are in the same diretory and work fine.
Sorry my nervousness. -
I do not know about the Webif, I do not use the Webif.
Why? if you are using oscam to read and serve cards then how do you actually know what is going on !.... or is oscam just reading your cards? either way you should be looking at what the oscam webif actually is :) especially if you use the software.
My config files, in Dreambox, are located in "etc/tuxbox/config/oscam".
Sorry my nervousness.
Its best you post your config files anyway even if they do work in a different receiver...however try location etc/tuxbox/config
Install all config files to the config folder and restart.
-
Open oscam.conf and look for [webif], you will get something like this;
Code[webif] httpport = [COLOR='#FF0000']8888[/COLOR] httpuser = httppwd = httprefresh = 15 httpshowpicons = 1 httpallowed = 192.168.0.0-255.255.255.255
In a firefox or chrome browser window type this and press enter http://192.168.1.95:8888 (change 192.168.1.95 to the ip address of your dm7020).. If you are prompted for a user and pass use what is set in [webif].. Show us the live log from oscam webif so we can help solve this.. If the webinterface doesn`t load oscam has not started..
Oscam can be started in telnet, paste these commands into telnet, pressing enter after each line.. Copy any errors you get and paste them here..
-
Why? if you are using oscam to read and serve cards then how do you actually know what is going on !.... or is oscam just reading your cards? either way you should be looking at what the oscam webif actually is :) especially if you use the software.
Its best you post your config files anyway even if they do work in a different receiver...however try location etc/tuxbox/config
Install all config files to the config folder and restart.
Yes I have been using OSCAM only to read my two cards (TNT and SmartHD).
I assume I have some difficulties in understanding and working with oscam but my configs have worked well until now and continue to work well in my ET9000.
I'm only using 4 configs and these are:-oscam.conf-
[global]
disablelog = 1
disableuserfile = 1
usrfileflag = 0
maxlogsize = 10
preferlocalcards = 1
saveinithistory = 1
lb_mode = 0
unlock_parental = 1[webif]
httpport = 8081
httpallowed = 10.0.0.0-10.255.255.255,172.16.0.0-172.31.255.255,192.168.0.0-192.168.255.255,127.0.0.1[dvbapi]
enabled = 1
au = 1
user = localuser
request_mode = 0
P: 0500:030B00
P: 0B01:0000-oscam.server-
[reader]
label = Card-TNT
enable = 1
protocol = internal
device = /dev/sci0
fallback = 1
detect = cd
group = 1
emmcache = 1,3,2
audisabled = 0
mhz = 500
aeskeys = 0500@030B00:0,F1DC...................
cardmhz = -1[reader]
label = Card-SMARTHD
enable = 1
protocol = internal
device = /dev/sci1
detect = cd
caid = 0B01
ident = 0B01:0000
group = 1
emmcache = 1,3,2-oscam.user-
[account]
user = localuser
disabled = 0
group = 1
au = 1 #Card-TNT[account]
user = localuser
disabled = 0
group = 1
au = 1 #Card-SMARTHD-oscam.whitelist-
i:0500:030B00:2013:4A8
i:0500:030B00:2027:4A8
w:These configs are working 5 stars, to read my cards (tntsat and smarthd), in my ET9000 with "oscam_1.20-rev-9810-Pli-4.0".
Same configs and same oscam version in my DM7020HD (with Pli4.0 image) do not work. I'll try "location etc/tuxbox/config". -
Open oscam.conf and look for [webif], you will get something like this;
Code[webif] httpport = [COLOR='#FF0000']8888[/COLOR] httpuser = httppwd = httprefresh = 15 httpshowpicons = 1 httpallowed = 192.168.0.0-255.255.255.255
In a firefox or chrome browser window type this and press enter http://192.168.1.95:8888 (change 192.168.1.95 to the ip address of your dm7020).. If you are prompted for a user and pass use what is set in [webif].. Show us the live log from oscam webif so we can help solve this.. If the webinterface doesn`t load oscam has not started..
Oscam can be started in telnet, paste these commands into telnet, pressing enter after each line.. Copy any errors you get and paste them here..
I'll try but it will not be easy due to my limited knowledge in this area.
-
It was easier than I thought to get the log (DM7020HD).
-
And now log from my ET9000.
-
Quote
2014/08/16 15:52:13 6B06B0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 16 ecmpids!
2014/08/16 15:52:14 6B06B0 c [DVBAPI] Demuxer #0 no suitable readers found that can be used for decoding!The latest versions of oscam require mhz and cardmhz parameter. Try adding these to both [reader] in oscam.server.
Each [reader] needs it`s own group, you have both cards in the same group. You also need an [account] that looks for both groups.
Restart oscam then show us the full live log from startup with any errors.
Code
Display More[reader] label = Card-TNT enable = 1 protocol = internal device = /dev/sci0 [COLOR='#FF0000']cardmhz = 2700 @@@WCF_PRE_LINEBREAK@@@mhz = 500[/COLOR] fallback = 1 detect = cd group = [COLOR='#FF0000']1[/COLOR] emmcache = 1,3,2 aeskeys = 0500@030B00:0,F1DC................... [reader] label = Card-SMARTHD enable = 1 protocol = internal device = /dev/sci1 [COLOR='#FF0000']cardmhz = 2700 @@@WCF_PRE_LINEBREAK@@@mhz = 450[/COLOR] detect = cd caid = 0B01 ident = 0B01:0000 group = [COLOR='#FF0000']2[/COLOR] emmcache = 1,3,2 -oscam.user- [account] user = localuser group = [COLOR='#FF0000']1,2[/COLOR] au = 1
-
Tank you, tank you, tank you! It's works now!
Just do not understand why with the ET9000 these changes were not necessary.
Greetings to all who helped me in this difficult.
Regards
-
I have a dm7020hd, it works fine
I tried different images OE2.0 as Merlin3, OoZooN, CVS, all work well
Why do not you try another image? -
As I said in my last post, the problem is solved. Tanks.
OSCam Support Forum
Configs, discussion, downloads and guides for OSCam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!