Yes..i have used the files u have uploded...the loader program and the firmware.. i even have download from amiko site and have tried to but whitout sucssess
Amiko Mini Combo won't boot
- padraig1
- Thread is marked as Resolved.
-
-
Have you checked the serial port
if its usb to serial then maybe the one you have is not working or talking to the box -
Yes i have..because when i have the jack 3.5 all input the pc doesnt detect the box..i need to puch a litlle the jack and after that the loader program run forward but doesnt pass that what i have already tell u... can u tell me what i have to choice ..upgrade mode or dumping flash?
-
Upgrade mode
you first load the FW make sure the box is turned off
Hit the NEXT button then plug in the box
If all is correct the flash will start working, can take about 15 to 30 min to finish -
Have you not got original software to flash on to usb?
-
Cannot be done with USB as main bootloader needs to be updated to 1.04 this can only be done with RS232
-
Im already on home and i have test e tried and nothing results...im not using usb plug..im using rs232 conect in pc and on the box are conected 3.5'jack (amiko mini combo)
- - - Updated - - -
Now i have buy a usb/rs232 adapter..and i have install the software...after that i have used the toolbox for amiko whit the firmware but nothing results ;(
I hve checked in "upgrad all" the msg i have is that " open serial port...
Sync to serial port...
get Client protocol veraion & chunk
Time out when read data!"And thats it...
i dont know what to do.. -
OK lets go back to the start
If your happy that the usb to serial cable is correct then follow thisUsing Toolbox for Amiko 3612 by Dekolte
Click Loader Amiko
Browse for the Amiko mini FW
Select the correct Serial port
Upgrade type all SW + Bootloader
Mode setting Upgrade
Click next
* NOW TURN ON YOUR AMIKO *Give it a few seconds it should start flashing.....
-
hopper is right. I was having the same trouble and had to realise - that the second after you click next then you power on the amiko.
the way I did it was have the power adapter plugged in to the wall and hold the dc jack at the back of the box. then the second after I clicked next on the loader I pushed in the DC jack. worked straight away. Thanks to freck and hopper for their help -
I have tried also that way...tomorrow im going buy new cable rs232 and try again in another pc...thank for the help ;)
-
looking firmware for amiko mini please if you can help
-
Here you go 1974
-
Amiko mini t2/cable
Could someone provide me with correct info to input.
for thetp index
frequency
symbol rate
modulation
lcn no or off ?????
on the wirral
Any help would be much appreciated
thanks -
Just before i try the method outlined on this thread are there a channel list included in the software ?
- - - Updated - - -
thanks for this post hopper
-
No Channel list only FW
I'll put one together laterRemember the method outlined above is only for boxes that wont boot.
-
Hi Hopper.I came here simply to thank your help. finally I managed. . . ;) it is only today that I had time. to have 2 small children is not easy to have time. but after having followed your intrucoes and with a new end I got for the box giving. Thankyou again hoper
-
No problem vascocaetano
Glad you are sorted
Thanks for the kind words. -
Hey,
Thanks for your help!
But in the topic says "Amiko Mini Combo"..... And you put the EMU of Amiko Mini -> HD <- ComboDoes this works for amiko mini combo? is not only for amiko mini HD combo?
Thanks for you help
Regards
Don't exist Amiko Mini Combo, are all HD ...
-
grazie compa
-
Hi
This is the correct EMU for the mini combothx hopper - was about to use my box for a door stop - hope santa brings u loooooads o prezzies :48_002:
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!