Usb Cardreader

There are 18 replies in this Thread which was already clicked 6,092 times. The last Post () by popo40.

    Hi thanks for a great forum. Just wondered if someone could help i have set up an old dell optiplex pc with debian 6 and CCcam 2.2.1 as per instructions and it is working well i have two dreamboxes loged on local network and a blade 7000 hd loged on over in france all seems well! The problem i have is my card reader witch i just recieved usb pheonix/smarmouse ftdi set at 3.3v/pheonix/6mhz it is showing up in devices as tty/usb0 so i have set it in config:

    SERIAL READER : /dev/ttyUSB0


    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 3570000


    BOXKEY: /dev/ttyUSB0 xx xx xx xx (as box)


    TRY ALL CHIDS : /dev/ttyUSB0


    It says in entitlements no card or unknown card inserted.


    Do i need to have keys channel info etc to read the card? Sorry i am new to all this but learning slowly thanks for a great start so far.


    This is the card reader: TBS 3102


    This is the most simple and strongest card programmer in the world.The USB smartmouse/phoenix card programmer has only 1 USB port,which is used for power and data transfer.Computer will look the card reader as COM interface after installing driver.This card programmer supports 4 Crystal frequencies(3.579MHz,6MHz,8MHz and10MHz) all selectable via dip switches, both 3.3V and 5V card voltage and Phoenix/Smartmouse working mode.

    It's ideal for programming, reading or writing of every smartcard iso 7816 Like M2Card, Penta VR3 Card, KnotCard1&2, GammaCard,TitaniumCard, OposCard, DragonCard, Anacondacard, TitanCard, Tita'mCard2, C***aCard and many others.

    As with other phoenix programmers an RS232 (Com Port) is not required because this programmer comes with an embedded FTDI chipset that enables Com port emulation on XP,Vista, Windows 7 & Linux Operating Systems, in addition it will operate on any digital satellite receivers with USB that support FTDI chipset (e.g. Dreambox).
    Whilst software for reading/writing smartcards is not included any 3rd Party Software freely available on the internet that supports phoenix/smartmouse mode will work. Drivers for Windows XP and other major Operating Systems can be downloaded from Virtual COM Port Drivers
    Main features:
    1.Dimension: 75x60x15mm
    2.Weight: 36g
    3.Cable connection: USB for power and data transfer.
    4.Prog. Mode: Phoenix/Smartmouse
    5.Power Mode: DC 3.3V/5V shiftable
    6.Frequency: 3.579MHz / 6MHz / 8MHz / 10MHz shiftable

    Specifications
    1 USB port Phoenix card Programmer
    5 Crystal frequencies(3.579MHz,6MHz,8MHz, 10MHz and 12MHz)
    3.3V and 5V card voltage

    hi there i have the same card reader and the same problem,


    did you mange to sort it in the the end and if so how??


    cheers

    it s simple to configure smartmouse


    in console in root user write


    lsusb -s


    linux say " Bus 003 Device 003: ID 104f:0002 WB Electronics Smartmouse "


    modprobe -r ftdi_sio
    modprobe ftdi_sio vendor=0x104f product=0x0002


    ls -al /dev/ttyUSB*


    response from terminal
    crw-rw----1 root uucp 188, 0 2008-05-08 10:59 /dev/ttyUSB0
    crw-rw----1 root uucp 188, 1 2008-05-08 10:59 /dev/ttyUSB1


    cat /proc/devices | grep -i "ttyUSB"
    response from terminal
    188 ttyUSB


    cat /proc/tty/driver/usbserial


    0: module:ftdi_sio name:"FTDI USB Serial Device" vendor:0c52 product:2101 num_ports:1
    port:1 path:usb-0000:00:1d.1-1.2
    1: module:ftdi_sio name:"FTDI USB Serial Device" vendor:0c52 product:e402 num_ports:1
    port:1 path:usb-0000:00:1d.1-1.4


    mknod /dev/ttyUSB0 c 188 0
    mknod /dev/ttyUSB1 c 188 1


    ls -al /dev/ttyUSB*
    chmod 777 /dev/ttyUSB*


    reboot your oscam or cccam


    note


    n this method is valid each redemarage sessions each machine you must repeat the manipulation al hour or day write these lines I am looking to automate the task for that it is recognized demarages

    What type of card are you using? Which company does it belong to? Is there a way to implement the same system on devices that use a coded system without a card? Can the same setup be done on these devices?

    Quote from electron112

    it work nicely with viaccess and more system


    im tested with viaccess and nagra card

    By Viaccess, I mean that some receivers use this encryption system, but the receiver doesn't have a card; instead, it has a code inside the receiver. I have a receiver that uses the Irdeto system, but the card is locked to STBID. I connected it to Oscam, and it read the card's data (ATR, CAID, provider, and serial number), but it still doesn't open the channels. This is the problem.

    exemple usb reader



    [reader]

    label = Tivusat

    protocol = mouse

    device = /dev/ttyUSB0

    caid = 183D,183E

    boxkey = *********

    rsakey = **********

    ecmwhitelist = 91

    ecmheaderwhitelist = 80308ED387,81308ED387

    detect = cd

    nagra_read = 1

    ident = 183E:000000,005411

    group = 1

    emmcache = 0,3,2,0

    lb_weight = 500

    dropbadcws = 1

    cccreshare = 3

    ccchop = 3

    auprovid = 005411


    [reader]

    label = Hustler

    protocol = mouse

    device = /dev/ttyUSB1

    disablecrccws_only_for = 0500:050F00

    caid = 0500

    detect = cd

    ident = 0500:050F00,FFF8F0

    group = 2

    emmcache = 1,3,2,0

    lb_weight = 500

    cccreshare = 3

    ccchop = 1

    auprovid = FFF8F0


    [reader]

    label = fransat

    description = fransat

    protocol = mouse

    device = /dev/ttyUSB2

    readnano = 9E200000000000000000000000000000

    caid = 0500

    boxkey = **********

    detect = cd

    ident = 0500:FFF400,041950,041960,041970,041980,0419A0

    aeskeys = ***********

    emmcache = 1,1,31,0

    lb_weight = 500

    dropbadcws = 1

    disablecrccws = 1

    ratelimitecm = 4

    ecmunique = 1

    ratelimittime = 9000

    srvidholdtime = 2000

    vu+ duo2,vu+zero4k,vu+ultimo

    dvbdream . haupage /tbs6983 vplug

    antenne bande c / 2.80cm/antenne ku/ channel master 150cm

    Edited 2 times, last by popo40 ().

    My problem is that I don't know how to use Rsakey; it requires someone experienced in reverse programming. Also, the boxkey in Oscam doesn't allow me to enter more than 8 digits.

Your resource for Linux TV servers and smart card readers.

Find software downloads, drivers, and support for server setup and card-sharing configurations. Set up a Linux-based TV server. Access downloads and support for server software and USB card readers for advanced TV reception and management

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login