oscam dvbapi with 2 cards

There are 16 replies in this Thread which was already clicked 4,688 times. The last Post () by codar.

    I have 2 cards in my duo2 0963 & mtv 0b00 and need to know if the below config will update them both using dvbapi?


    oscam.conf
    [global]
    nice = -1
    waitForCards = 1
    clientTimeout = 5
    cacheDelay = 120
    logfile = /var/log/oscam.log
    disablelog = 1


    [dvbapi]
    enabled = 1
    user = linuxsat
    boxtype = dreambox
    au = 1


    [webif]
    httpport = 8888
    httpuser =
    httppwd =
    httprefresh = 15
    httpallowed = 192.168.0.0 - 255.255.255.255
    debug = 255


    oscam.server


    [reader]
    label = MTV
    protocol = internal
    detect = cd
    device = /dev/sci0
    group = 1
    caid = 0b00
    ident = 0b00:000000
    emmcache = 1,3,2


    [reader]
    label = SKYUK
    protocol = internal
    device = /dev/sci1
    blockemm-unknown = 1
    blockemm-g = 1
    saveemm-u = 1
    saveemm-s = 1
    emmcache = 1,3,2
    group = 2
    caid = 0963


    oscam.user


    [account]
    user = linuxsat
    pwd = ****
    group = 1, 2
    au = MTV, SKYUK


    Thanks in advance.


    - - - Updated - - -


    Bump. Sorry if I'm being inpatient but I've just upgraded my uk card and I haven't received the EMM yet.


    Using the latest version of oscam on vix

    No and yes is your answer , you would need to have trusted peers with au enabled for these cards pointed at the satellites in question , you alone would only point at either satellite
    Your entitlements should update in minutes also if you upgraded and all is in order

    Edited once, last by stevejo ().

    [account]
    user = linuxsat
    pwd = ****
    group = 1, 2
    au = MTV, SKYUK


    I've noticed if I set au to = both readers oscam auto selects the first reader only so I don't think both cards will update with au set to one of the readers, am I right? Would I need to set it to 1?

    Edited once, last by ste141 ().

    Quote from ste141

    [account]
    user = linuxsat
    pwd = ****
    group = 1, 2
    au = MTV, SKYUK


    I've noticed if I set au to = both readers oscam auto selects the first reader only so I don't think both cards will update with au set to one of the readers, am I right? Would I need to set it to 1?


    au = MTV, SKYUK it's right
    it's important to enable other users
    which protocol are you using?

    together we grow - ferdi

    Hello everyone its good to be back been away for a while.


    As stated in previous post when I set au = MTV,skyuk will auto select MTV when I save config. Would setting au = 1 be the solution for updating 2 cards without having to select one or the other every time I want to update a card ?

    • Official Post
    Quote from ste141

    Hello everyone its good to be back been away for a while.


    As stated in previous post when I set au = MTV,skyuk will auto select MTV when I save config. Would setting au = 1 be the solution for updating 2 cards without having to select one or the other every time I want to update a card ?


    The wiki states - au = 1 # auto AU is sending EMMs to all readers.. So you don`t necessarily need the label of the reader.


    You could try adding auprovid = 0963:00000 & auprovid = 0b00:000000 to each reader. set provider ID to use the right reader for auto AU.

    au = 1
    Or
    au = slyuk (or whatever your reader is labelled/called)


    Dvbapi is needed if your server is on a receiver which you use to watch tv.
    Without it, oscam cannot decrypt / de-scramble the channel.

  • master G

    Set the Label from UK OSCam to Videoguard2 Cards OSCam

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login