Card in Smargo gets no ecm-no entitlements

I have my Smargo in a hub, and my Oscam webinterface says: "Status OFF" (No entitlements). It does'nt open up the card. Soon posting log...

(I know the crad works (updated) in the original receiver.)

when I run dmesg I get this:

drivers/usb/serial/ftdi_sio.c: ftdi_tiocmget Could not get modem status of device - err: -19
drivers/usb/serial/ftdi_sio.c: ftdi_set_termios FAILED to set databits/stopbits/parity
drivers/usb/serial/ftdi_sio.c: ftdi_set_termios urb failed to set baudrate
drivers/usb/serial/ftdi_sio.c: urb failed to clear flow control
drivers/usb/serial/ftdi_sio.c: ftdi_tiocmget Could not get modem status of device - err: -19
drivers/usb/serial/ftdi_sio.c: error from flowcontrol urb
drive
rs/usb/serial/ftdi_sio.c: update_mctrl Error from MODEM_CTRL urb: DTR LOW, RTS LOW
ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
usb 1-2.2: USB disconnect, address 5
ftdi_sio 1-2.2:1.0: device disconnected
drivers/usb/serial/ftdi_sio.c: error from flowcontrol urb
drivers/usb/serial/ftdi_sio.c: update_mctrl Error from MODEM_CTRL urb: DTR LOW, RTS LOW
ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1

Smargo not working?

Thx for your reply. My mistake...:ops: I had the card upside down. REMEBER: CHIP UP!!!

My working settings:

CCcam config.

N:127.0.0.1 10000 localuser oscamserver10000 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

SERIAL READER : /dev/ttyUSB0
SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 3570000

Oscam:

[global]
serverip = 127.0.0.1
usrfile = /var/log/oscam/oscamuser.log
logfile = /var/log/oscam/oscam.log
cwlogdir = /var/log/oscam/cw.log
cachedelay = 120
nice = -1
maxlogsize = 500
preferlocalcards = 1
saveinithistory = 1

#[monitor]
port = 988
monlevel = 4
nocrypt = 127.0.0.1

[newcamd]
port = 10000@093E:000000
key = 0102030405060708091011121314

[cccam]
port = 15500
reshare = 1
forward_origin_card = 1
version = 2.1.3
updateinterval = 240
keepconnected = 1

[webif]
httpport = 3001
httpuser = root
httppwd = xxxxxxxxxxxxxx
httprefresh = 10
httpallowed = 127.0.0.1,192.168.1.1-192.168.1.150
httphideidleclients = 0
httpreadonly = 0
httpsavefullcfg = 0

[reader]
label = Smargo
enable = 1
protocol = mouse
device = /dev/ttyUSB0
caid = 093E
ident = 093E:000000
boxid = xxxxxxxx
detect = cd
mhz = 357
cardmhz = 357
group = 1
emmcache = 1,3,2
lb_weight = 100

[account]
user = localuser
pwd = oscamserver10000
group = 1
monlevel = 4
au = Smargo
caid = 093E
ident = 093E:000000

This is working settings for 093E card in Vu+ Duo with Black hole 1.6.6 image. Oscam 1.20 unstable 5985/ CCcam 2.13.

Yes I have..thx. Working find now. Card is a bit slow in opening. Maybe I shall change the reader settings...?

master G

You're so right. I can't have double cardreaders......Thx

Quote from daniel2005

Why are you using ccam with oscamon the same machine, just activate the dvbapi in oscam conf and remove cccam on this machine. update of you card will most likely bettter happen with oscam alone

I'm new to Oscam and trying different combos to get the fastest ecm time. I have an Nds card, using a Smargo in a D-link hub, and getting "slow" ecm times. Between 350-400. I have a Conax card in my DM600 in my bedroom, sharing between them, and the Conax card open up a lot faster (on Vu+) even though it "travels through" Homeplugs etc, to my Vu+ in the livingroom. I think I should be able to get around 150-200 on my NDS card. It does'nt matter if I set 357, 500 or 600mhz in Oscam config.
I tried Oscam dvdapi, Camd 3.57 and CCcam. Any other ideas?
The hub is a few years old, but power supplied and using usb-2.0.

fogonero!
I tried your suggestion and I'm getting ok answers:

/usr/sbin/hald
/usr/sbin/pcscd

Still bad ecm times though...strange is that it does'nt matter how I set the reader settings, 357, 500 or 600 mgz. Thx for helping