hi guys, i try the recovery from post #13, i run the program as arm in, user the pinhole for 10 seconds. but nothing happens.
dead wetek?
- gitiro
- Thread is marked as Resolved.
-
-
is the same then my post #8 looks like you dont want my so i will nothing more say on this topic
1 thing i have use this +- 10 times works for me good -
this is my putty log
EEEE I3000000032940xf3001103 03;77520EEEE I400000004294_M6_BL1_3431 >2534313
TE : 77476
BT : 11:09:43 Mar 26 2015CPU clock is 1200MHz
wait pll-0x03 target is 0204 now it is 0x00000203
DDR clock is 516MHz with Low Power & 2T mode
DDR training :
DX0DLLCR:40000000
DX0DQTR:ffffffff
DX0DQSTR:3db05001
DX1DLLCR:40000000
DX1DQTR:ffffffff
DX1DQSTR:3db05001
DX2DLLCR:40000000
DX2DQTR:ffffffff
DX2DQSTR:3db05001
DX3DLLCR:40000000
DX3DQTR:ffffffff
DX3DQSTR:3db05001
Stage 00 Result 00000000
Stage 01 Result 00000000
Stage 02 Result 00000000
Stage 03 Result 00000000DDR init use : 42472 us
HHH
BootFrom SPI
ucl decompress
decomprõclr h-ram
DRAM: 1 GiB
relocation Offset is: 105e0000
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
NAND: Amlogic nand flash uboot driver, Version U1.06.020 (c) 2010 Amlogic Inc.
SPI BOOT : continue i 0
No NAND device found!!!
NAND device id: 2c 44 44 4b a9 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron D revision NAND 4GiB MT29F32G08CBADA)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =168,aml_chip->oob_size =744,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=744
aml nand env valid addr: 0 ,status =0
key start_blk=2040,end_blk=2047,aml_nand_key_init:684
aml nand key valid addr: ff000000
aml nand key valid addr: ff200000
aml nand key valid addr: ff400000
aml nand key valid addr: ff600000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
NAND bbt detect Bad block at 0
Creating 2 MTD partitions on "nandnormal":
0x000000800000-0x000001000000 : "mtd1"
0x000001000000-0x000008000000 : "mtd2"
nandnormal initialized ok
detect mx chiprevD :1 and nand_type: 40
nand_curr_device =1
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
SF: Detected MX25L3205D with page size 256, total 4 MiBSPI NOR Flash have write protect!!!
In: serial
Out: serial
Err: serial
register usb cfg[0][1] = 9fe85cf4
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- : 5 4 3 2 1 0
exit abortboot: 0
Amlogic Ethernet Init
Success: reset mac OK!(0)
ETH PHY hardware reset OK
find net phy id=0x7c0f1, phyad=1
set_mac_mode(0)
final_addr[rx-tx]: 0x9feee000-0x9feee600
Ethernet reset OK
MAC address is e8:18:63:50:2f:b8
phy auto link failed
half duplex
10m
BOOTP broadcast 1
phy auto link failed
phy auto link failed
BOOTP broadcast 2
phy auto link failed
phy auto link failed
BOOTP broadcast 3
p- - - Updated - - -
anyone now this error at start up wetek?
BOOTP broadcast 1
phy auto link failed
phy auto link failed- - - Updated - - -
hi guys, my problem is solved.
i get good online help from wetek servicedesk.thanks paulo.
this is what my problem fixed.
Your uboot seems to be searching some network, I'll give you some instructions in order to erase the enviroment variables:
Turn Off your WeTek by unpluging power cable
Connect debug cable and start a terminal session
Turn On WeTek, pluging in power cable
As soon first log lines appear break boot by pressing CTR+C
You should see now prompt "wetek#" and enter now this commands:
sf probe 2
sf erase 0x100000 0x8000
reset -
this must works http://wetekforums.com/vb5/for…-howto-unbrick-wetek-play
dead link dead wetel the usb tool link broke please help USB Image Tool" broke
-
USE the link on page #11
dead link dead wetel the usb tool link broke please help USB Image Tool" broke
-
master G
Moved the thread from forum WeTek Play Support to forum WeTek Play. -
master G
Moved the thread from forum WeTek Play to forum WeTek. -
try this Honcho, http://linuxsat-support.com/attachment.php?attachmentid=33728&d=1431865882
* Power off your device and unplug the AC power cord.
* Download the recovery zip (below you will find the up to date version).
* Unzip the downloaded zip (you can delete the META-INF folder).
* Copy the downloaded zip and the freshly unzipped recovery.img to a MicroSD card.
* Now insert the MicroSD card in your STB.
* Plug the AC power cord while you keep pressed the little reset pinhole (located on the bottom of the device) for 10 seconds (just count slowly to ten and it will be good).
* The device should have booted to CWM recovery.Hello, can you guys provide the files again? Thank you
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!