Posts by annie12

What images are you using ? the motorised wont make a difference to cams LOL

Have you got this in oscam server
[reader]
label = ****K
protocol = pcsc
device = 0
post your configs leaving out the ****** bits and it might help
on some setups you don't even have to #out any thing (single reader setups)
did you update/install pcsc "apt-get install opensc" ??? hope this helps annie.

Have you got ubuntu if so have you putty and ftp software ???

Here is another way of installing WEBMIN worked perfect 4 me
Tried this on ubuntu it works 10.4/12.04 tested
log on to server then go winscp/putty
copy and paste in putty ect 2,3,4
1 sudo -i
2 wget -c http://www.webmin.com/download/deb/webmin-current.deb
3 sudo dpkg -i webmin-current.deb (ignore the errors)
4 sudo apt-get -f install (this will fix the errors/dependencies, , recompile, and install webmin.)
Now, login to your webmin server.( your own pc)
( example: https://192.168.1.36:10000/ )
then use your login/password, argree if you have to in firewall

On the new bh2.0.0 oe2
Tried using master g ipk got he green screen then decided to do what i done in vix
ftp 2.6 version over to folder already created from the ipk install
it would not allow the folder /.cache_httplib/ so i did not ftp it..
may be permissions?? did not bother to try, rebooted
perfect LOL

hi jumbi go to ..
http://linuxsat-support.com/en…ons-server-updates-7.html
you can then update it if you want
ps sent you a message

hi all gave this a try, sure enough got the green screen on system info exit
so updated to senns69 link ok..setup tuners, used dreambox edit sent my
favs ect over, installed tspanel then cams ok.
as per norm. epg, swap ect.. anyone able to explain how to use meboot
what files do zip to get it to work?? i am trying to get my vix
in there as well TIA

if you are using usals in the tuner setup with a proper image, catseye/vhannibal E2 settings
should do the trick, You dont store@ every position, what motor r u using ??

hi mrgmx i fpt it to the folder on the vu then hard reboot (disconnect mains)
the same way to get the 1channel working and noticed the files ending with
.pyo in the resolvers folder then no "gsod" LOL

first goto intelsat1w or thor 0.8 [if in ireland goto atlantic bird 5w] this is you ref sat.
go to the menu where you can change between diseqc and usals. if your dish was set up with usals then the settings should already be there.
here you will see the Longitude and Latitude. Slightly increase your longitude, prefrably by 0.5 and press `go to position` [or whatever your reciever says] check if the signal has increased or decreased. If it has increased then you are going the right way and hen add 0.2 if it has gone down take away 1.0(0.5 to compensate for your first attempt and the other 0.5 to go the other way) if the signal goes up, add another 0.2 if down then your original alignment was perfect.
at this stage if you have not been able to improve you signal then get out to the shed and bring out the ladder. you will need to skew the lnb. but first make sure you have a marker to mark the lnb`s current skew. once you have done that slightly turn the lnb both ways until you have peaked the signal.
then you should be sorted.
please inform me if you think ive missed anything out as this has come out of the top of my head, [i learnt this 6 months ago].
if you are using usals to move your diseqc motor you will need to put in your longitude and latitude for your location.
go to multimap.com and enter your postcode when done so below the map you will get your longitude and latitude

eg.
Lat:51:32:32N (51.54227)
Lon:0:44:43E (0.74537) if this has a minus it means west
always use the numbers in the brackets.
look at your motor settings >usals/gotox and see how many numbers it can fit.
for the TM it is xx.x
so you will have to round the figures up/down to fit so in the TM I would put-
latitude 51.5 N
longitude 0.7e
if your receiver take more numbers you can put it as on the multimap but I just use extra 0's
latitude 51.500 N
longitude 0.700 E
cant remember were i got this, See post 17 as well Remember "Atlantic bird 5w"
is your most south position eg...goto " 0 " ,,,remember the world is not round you
have to get it into an arc.. Your setting should be about 053.000 north _008.200 west.
when your almost/finished you can tweak the 008.200 eg change to 8.100/7.900 and so on
Till you get the strongest signals
hope this gets you going..LOL

Got the 2.6 version working perfect on an vix 2.2.1 image this is only 1 i could get working
without the green screen of death, crashing thanks

If you in ireland near (s/w limk) do not 0.8 as a ref use Atlantic bird 5w. as your
reference point eg.. goto "0" set it here it should look straight pointing south,
then swing disk to say 13' fine giving it gink left right up/down very slightly
then go 28' same and so on till you get happy go lucky position
PS dont be to worried if you have to change the long/lat mine at the mo
is 8.200w my real is about 8.6 so you might have to tinker
a little with these again till you reach a happy medium
hope this helps LOL..

I'll have to agree with caz
4 a newbie i like to know 2.1.1 as well

HI nano, i not having a argument, just stating the fact that most psu' units for laptops these days
are in the region of 18-22v, some have 3 wires 1 is for sence eg.
dell so you have to buy the right replacement. i have not seen a 12v one
in an age all i was trying to get across if some one connected that to the dm
he would not have a problem with it any more, as it would be fokced LOL

A Laptop psu will not so ad the voltage on most is between18-22volt
if you have a psu for a external hdd they are normally 12volt
the current needed is 2/3 amp, if you have a 12volt psu
center pin positive if you have 2/4/10 amp the amp will not matter
as the dm will only draw what current it needs (AMPS).
but the volts will 12-13.8 volts only...

Dream control center )DCC as its known lol

no it wont read zips usually .img have you dcc installed on you windows
if so you can do by telnet ? or do you have dreamup?

Hi all is there any such solution or fix for omnikeys i done thatfellows 64bit version ubuntu
and on reboot the omikeys go all over the place, originally i taught is was
the oscam was the fault
thanks in advance

if its CUSTOMERS you deal with I think your in the wrong place

hi lads installed thatfellows Automated Oscam/CCcam 2.1.3
Install Package For Latest Ubuntu 12.04 amd.64-Bit
a bit of a pain getting to work.
my problem now is trying to get 2 omnikey's
to work in oscam 1 no problem, but when i add the 2nd
omni in oscam server/newcamd port thats it it will read
my sly entitlements but wont work.
Dont have this problem on 32bit oscam8077
-i686-pc-linux-webif-ssl-pcsc-libusb-Distribution.tar.gz
just wondering is there a 64bit oscam like pcsc-libsus ect..
i think it is oscam is causing my problem TIA..