Posts by robocop

Hi looking for a image for a DM800 clone sim 2.01 bootloader 72 with the cool epg on it can anybody help

cheers.

Thanks Ten yep i entered it wrong in the config file and forgot the ecmwhitelist = just could not see it
just like to say thanks for a great forum and all your help

Cheers

Hi just included your whitelist in my config the problem i had with my whitelist some channels not clearing i stuck your list in all channels cleared but after 2 min card stops working hashed whitelist all ok again any ideas what could be going wrong here is my config

[reader]
label = s#y_#k
protocol = pcsc
enable = 1
detect = cd
device = 0
emmcache = 1,3,2
caid = 0963
ident = 0963:000000
cardmhz = 357
boxid =
group = 1
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
lb_weight = 101
#0963:3E,4E,4F,42,44,45,47,53,54,56,61,6A,6B,6D,6E, 6F,62,67,68,69,7A,7C,7D,7E,71,72,73,74,77,78,79,80 ,8B

[global]
nice = -1
logfile = /dev/null
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1

[webif]
httpport = 8888
httpuser = ####
httppwd = ####
httprefresh = 5
httphideidleclients = 0
httpallowed = 127.0.0.1,192.168.1.100-192.168.255.255,192.168.#.6#
debug = 255

[newcamd]
key = 0102030405060708091011121314
port = 10002@0963:000000

[account]
user = ####
pwd = ####
group = 1
monlevel = 1
uniq = 2
group = 1,2
au = s##-#k
caid = 0963
blockemm-u = 0
blockemm-s = 0
blockemm-unknown = 1
blockemm-g = 1

ok just a update to the problem i have plugged the reader into my windows pc and installed drivers when i push the card into the reader the green light starts to blink red i asume it is reading the card this does not happen on my linux system so it looks like the reader is ok so i am going to reinstall omnikey drivers next to see what happens.

cheers.

Thanks I have done a update and reinstalled the drivers also the reader is brand new from our sponsers The sat shop i will plug it into my windows pc to see what happens

Thanks for your help

root@cccam:~# opensc-tool -R
[opensc-tool] reader-pcsc.c:1015:pcsc_detect_readers: returning with: No readers found
Configured reader drivers:
pcsc PC/SC reader
ctapi CT-API module
root@cccam:~#

hope this helps cheers

Quote from Ten Below

Here you go mate, it goes to /etc/opensc/ correct permissions are 0644, make sure you do the last part of the guide if you havent already.

How to disable pcscd never ending loggin to /var/log/messages what can write your /var partion full after some time.
Please enter next commands under putty or over terminal command line as root:
nano /etc/init.d/pcscd

There look next lines:
# if you need to pass arguments to pcscd you should edit the file
# /etc/default/pcscd and add a line
# DAEMON_ARGS=??your-option?

And please change it to:
# if you need to pass arguments to pcscd edit to:
# /etc/default/pcscd and add a line
DAEMON_ARGS="-e"
And hit from the keyboard ctrl+o and enter to save the changes and ctrl+x to exit

Now Reboot server and this command on restart

Code

opensc-tool -l

Display More

Thanks Ten but still no luck i copied your file in opensc also added in DAEMON_ARGS="-e"
still getting
[opensc-tool] reader-pcsc.c:1015:pcsc_detect_readers: returning with: No readers found
No smart card readers found.
root@cccam:~#
and can still see it connected on lsusb Bus 005 Device 003: ID 076b:3021 OmniKey AG CardMan 3121

i have moved the reader around different usb ports and can detect it in each port
i reboot machine each time do i need the card in for pcsc to detect the reader
cheers

Quote from nirmies

Did you follow the tut How to install Omnikey readers on Linux PC in the tutorial section by master g? If not try that.

yes i have tried that it must be in that opensc config somewhere but i cant find the problem does anybody have a copy of a working opensc config file or how to do reinstall of opensc pcscd libccid on debian

Thanks

I to have a problem with omnikey on debian 6 if i run lsusb i get

Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 076b:3021 OmniKey AG CardMan 3121
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
then i run command
opensc-tool -l
and i get
[opensc-tool] reader-pcsc.c:896:pcsc_detect_readers: SCardListReaders failed: 0x 8010002e
[opensc-tool] reader-pcsc.c:1015:pcsc_detect_readers: returning with: No readers found

has anybody any ideas why i cannot find the card reader i have tried everything i know but no luck

Thanks

yep CCcam cheers

Hi i bought a original smartreader + and was installed on debian 6 with ### uk card running on 3.59mhz fixed, all was good for 3 weeks until 2 days ago when the reader stopped reading the card. The only thing before i started using the reader i updated the the software to the 1.5 version which i have been told is not good, i also have downloaded the dealerfix software to return it to ver 1.3 but it does not seem to work on my pc running xp, i have searched the forum to find if anybody has had a the same problem i have run dsmeg and i get this line so i think it can see the reader ok, running CCcam 2.14 on its own also the card works fine in my dm800 has anybody else had this problem cheers

[ 74.356909] ftdi_sio 4-2:1.0: FTDI USB Serial Device converter detected
[ 74.356944] usb 4-2: Detected FT232BM
[ 74.356946] usb 4-2: Number of endpoints 2
[ 74.356949] usb 4-2: Endpoint 1 MaxPacketSize 64
[ 74.356951] usb 4-2: Endpoint 2 MaxPacketSize 64
[ 74.356954] usb 4-2: Setting MaxPacketSize 64
[ 74.358032] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 74.358176] usb 4-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 74.358203] usbcore: registered new interface driver ftdi_sio
[ 74.358207] ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver

Thanks guys i think i have found the problem homehub 3 only gives you one ip that you can portforward and create a static ip and my dm800 is using it it seems this is a major fault with the homehub 3 and bt are trying to sort out the software

Thanks

Hi i have a cccam server running on my dm800 works ok but i was going to run it on the pc so i read the tutorials and downloaded debian 6 and used auto install for 2.21 but my problem starts after i put in static ip and sub net, i know how to get the correct settings from cmd but no matter what i do after i have put in static ip then rebooted it will not connect to my router i have also left the ip and all the settings blank but still no connectoin i have a home hub 3 router which are not good but has anybody else had this problem

cheers

cheers i just tried cable swap no luck going to get new lnb thanks for your help

Can anybody help with this problem ok i have a s#y box which i use for the mrs and off the same lnb i have dm800 the s#y box has 2 cables and dm800 has one, the dish has a 4 port lnb when the s#y box is on i can only get vertical channels on the dbox but as soon as i pull the power on the s#y box i get Horz and vertial back any ideas how i can get both to work

cheers

Okay i tried the { 0:0:2, 963:0:0 } at the end of the cline but i cannot connect to the server if i remove the line connection is perfect any ideas

cheers

Thanks for your help i will test out yor suggestions

Hi i have 2 c lines from different servers both have uk channels and one of them has eu stations as well, is it possible to give priority to one one of the servers as it is more stable on uk channels

cheers :65:

well set the motor to 0 deg then input lat long into the dm800 still the motor will not move more than one step also noticed that it will not drive when a v-transponder is selected only a Horizontal i think its the motor i might have to take a look inside it

ok Thanks i will try that.:83: