Posts by abu baniaz

Ditto last two posts. I reserve IP addresses on my router. Never have to worry about setting network addreses, they stay the same.

The four nations were initially split to allow for HD Swap. Some regions had HD channels and others not. As most people are now using SD regions, there was no need for the segregation, so they have been unified. The republic of Ireland is a separate provider, so this remains separate

You may wish to try the Sly ZZL by ZoomZoomLuke. It will skip all the unavailble HD channels.

Attached is the 13 Nov 2014 "test version". Source files are on Lraizer's home forum. This is the feeds from Apollo 98 so can be installed through plugin downloads menu. Package contains: mips32el ipk, sh4 reader and plugin folder for manual installation.

Are you sure you are using correct address? Clicking banner on top of forum works.

Did you replace the mg_cfg, i.e use the one from your DM500?

Dont use sites like that. You dont want to expose your friends to such sites.

If you are using windows, deafult is not to show file extension. Make sure you dont make the file newcamd.list.list

Editing file taht is installed is safest way.

Start on a fresh image to rule any issues out.

Depending on where you got your ipk from, some do not have the configs.

Downlaod from here, they'll have the configs.
http://linuxsat-support.com/showthread.php?t=1689

Has been fixed.

https://github.com/oe-alliance/oe-alliance-plugins/commit/6c8df8b10c54aab3f4186b57e98d4198a624dd07

Thanks.

It is not an image issue, it is an ABM issue. Will be looked at.

Ten Below
Did you transfer with Dreamset or dreamboxedit on OpenATV? If DBedit, did you save first then transfer?

In /etc/enigma2/bouquets.tv are the entries for Catseye's ones

#SERVICE: 1:7:1:0:0:0:0:0:0:0:userbouquet.ED07.tv
or
#SERVICE 1:7:1:0:0:0:0:0:0:0:FROM BOUQUET "userbouquet.ED07.tv" ORDER BY bouquet

Thanks in advance.

- - - Updated - - -

stevejo, can you put enigma to sleep first and replace the bouquets.tv file with the attached. Run ABM after restarting.

Need to confirm somthing. Thanks in advance.

I would like to reiterate that the satellites.xml is not used by AB 28.2. The only value used in there is the presence of 28.2.

Quote from Thedan55

I did that, it's still the same size!?!? :eek:
Is there a way for me to record one channel and watch another? The uno has to sat plugs, one says in and the other says loop, what's that second plug for?

What tuner do you have? A single tuner with loop out, or a twin sat tuner?

The matter needs to be investigated...

Anyway, just for clarification:
The list of satellites in the satellite.xml affects what satellite are available to the user.
The list of transponders in the satellites.xml affects what frequencies E2 scans during a normal scan.

These are not used for blind scans. ABM, AB 28.2, AB N1, AB E1 also do not use these values as they are not normal E2/E1/Neutrino scans.

For tuning, only the lamedb file is used.

@TenBelow
Which build of OpenATV are you using?

Which image number are you on?

If using ABM, you don't need to look for the xml its there already. Has been in the image for a few months.

Can you see $ky ZZL as a provider?

Are you using AutoBouquetsMaker or Autobouquets E2 28.2

Use ZoomZoomLukes xml and enable swap.

If you're using latest images, the xml is there already. Select *** ZZL.

Quote from voyager1972

ive just setup this image on my dm500 ,,,everything working fine,,,just wondering is there any way to set the channels to my region "n.ireland",,,,

Blue > Commando Toolbox > 28.2E AutoBouquets Wizard > 28.2E Set My Location Wizard

Open your bouquet list, (it will be blank), Green (for satellites), Cable services.

Select a channel that shows a picture, perhaps BBC Two. then run Autobouquets for cable. 00015 wont be listed, select "Pure/first found"