Have you got any other client boxes connected?? NO
Have you got any problems with your own server?? Not sure what you mean?
In my router the box was assigned 0.6
And from my pc to box it was 0.7
Setup both ip's to 0.7 it has improved but when it freezes it clears after a few secs.
Will download CCcam later and load cfg file and see how it goes.
Here is my speed test not sure how to add to my profile
http://www.speedtest.net/my-result/4649202875
Internet is fine i can go into iptv or kodidirect and stream no problem
I have vu solo2 with the latest vix image 04 and got latest oscam from plugins.
I have three c-lines and put them into cccam to oscam converter. NOT PAYSERVERS
They work ok for ten min and freeze for 30sec than come back ok.
It has been the same for about two weeks with different lines
Signal is ok 92% sat
Just getting use to C- line and Cccam to oscam converter to convert to oscam works great.
But i am seeing a lot of f- lines NOT PAYSERVERS.
In the convertor you c-line/f-line/n-line.
My question is can you mix and match or only type of file.
Forgive my ignorance as i have just got use to cccam to oscam with c-line
look at getting a subscription to shareHow do i do that M8
Sorry about this post http://linuxsat-support.com/showthread.php?t=78984 was tired and did not think.
Here is my setup:
Triax Imtr dish, Spiderbox 6000, Vu Solo2, Inverto Black Ultra twin lnb, Dark motor.
LNB1 on spiderbox connected to motor to move to different stats.
LNB1 on Vu box connected to 2 on LNB.
Router is upstairs connected via Homeplugs and network switch feeding the two boxes downstairs.
I am getting freezing on both boxes at first i thought i was the the cline on my vu but i am getting the same on the spiderbox with the gift .
On the Vu box i thought it was CCcam so changed to Mgcamd and the Oscam same results.
Spiderbox gift is still active.
Signal and quality on Spiderbox is 80% and 83%.
Signal and quality on Vu box is 95% and 93%
Speed on homeplugs is 149 local 97 remote.
Checked ends of lnbs going to boxes ok
Changed network switch and cat5e cables.
Anybody advise what could be wrong.
Working fine until a few weeks ago that's when i starting checking everything.
Not sure if i have done this right.
Tried Oscam last night loaded softcam and files conf, user and server from here
Used cccam to oscam generator and put a c-line and converted it and saved it as server file and loaded it.
Started oscam in soft cam manager and clears for 20 secs and freezes for a few seconds and clears again does this all the time .
Not sure what i am doing wrong as this the first for me to try Oscam.
I hope i have not broken any rules.
Thanks
Thanks M8 changed the cfg file recorded a few hours overnight last night was still on this morning. Have not had chance to check will do later on tonight
Thanks for the reply M8 still learning myself
I have installed Mgcamd 1.38 on my VU slolo2 in var keys this is what i have.
ccamd.list
Mfg.cfg
Newcamd.list.
Put the clines in ccamd. list and cws in newcamd.list
I have stopped cccam 2.3.0 in cam manager.
I updated the vix image online yesterday
Start Mgcamd in softcam manager works ok for ten minutes then switches it self off and starts CCcam again
Restart Mgcamd and disable automatic startup for Cccam but same thing happens
What am i doing wrong
If your budget will stretch to £260:
Go for the Solo2 it's one purchase you will not regret
With openvix i have loaded cam4me-feed-configs_1.0-r0_mipsel.ipk. CCcanm.cfg.
Downloaded cccam 2.31.0 i think is the number.
Put a few a few fictious clines in the CCcam.cfg activated it says cannot connect to webpage.
Not bad for a novice only had the box over week and just tried doing this last night.
Just to find a cline that works .
Thanks for all the tutorials on here i am getting there.
Just tried updating downloaded updates rebooted by itself stuck on powerboard logo again
Just loaded OPENVIX image it loaded fine so it's not the stb
Just found out the one in the link is experimental dated gb800seplus-PBNIGMA-VX-3.0-1-20140507_EXPERIMENTAL_usb.zip does not work.
The one that works ok is gigablue_bootloader_gb800seplus_20131102(5).zip. But if i try to update it loads files and reboots and gets stuck on 49% and red strip light stays on .
It was the the image.
After trying to load it i put OPENIMPS 4.1 on it loaded great
The link you mentioned in post 6 i downloaded after registering that was the problem .
This time i downloaded from the site same usb stick loaded great.
Thanks for all your help and advice
Downloaded image and loaded it.
Goes through the process from boot,conf then ok .
Then the powerboard logo comes on the screen the display flashes 25 to 100 then stays on 100 and the red light stays on the panel with the powerboard logo on screen.
reflashed a few times still the same
Thank you very much M8 registered still waiting for link in my email says it should take about ten minutes my German is rubbbish
