On SF8008 4K with OpenAtv 7.3 MultiStalkerPro works perfectly
Posts by corpina
-
-
OK!
Thanks!
-
The TV Series option doesn't work with this version MultiStalker why?
-
Thanks Ziko!
CodeThe only thing I don't like is the Picons being on the right side and the EPG information on the left side -
work perfect in OpenAtv 7.1 and OpenAtv 7.3
Is there already a Telnet command to install and uninstall Multi-StalkerPro or is there still nothing?
-
Code
Thank you for your help I've done what the manual says. The VPN turns on but after a few seconds it turns off again -
Code
Can someone explain to me how and where to put the login data of a vpn (username and password), in OPENVPN? I have a vpn (ovpn), but I can't get it to work because I don't know how and where to put the login data. Box Octagon SF8008 Image OpenATV 7.2 or 7.1 Please help me! -
Please can someone help me? I have the OpenAtv 7.2 image and Multistalker 1.5 installed. Until yesterday everything worked perfectly but without doing anything, the multistalker stopped working any MAC I use always gives the same error when I try to access it always says: LOGIN FAILED I'm sure the MACs and addresses are ok. Can someone help me and explain what to do?
-
Code
I downloaded and installed this Softcam ( OSCam-11718-798 (armv7ve libusb)), on my SF8008 4k box, installed by IPK but the box doesn't recognize this softcam. I wonder why? -
Display MoreCode
Where? I've looked and I can't find itopen DreamSat Panel
go to the Media section
install - MULTI STALKER ALL PYTHON
Code
Display MoreDoes not work! I can't open DreamSatPanel! I used this command to update: wget -q "--no-check-certificate" http://ipkinstall.ath.cx/ipk-install/DreamSatPanel/installer.sh -O - | /bin/sh gives this error: Skin is not supported DreamSatPanel works only with FHD skins I have the OpenAtv 7.0 image installed and my box is an Octagon SF8008 4K -
Update multi-stalker version 1.4 for all python in the Dreamsat panel in the media section
CodeWhere? I've looked and I can't find it -
Do you have mgcamd installed already?
Post an example of the NCamd lines.
Code
Display MoreDirectly from the box (plugin/softcam), I installed : Oscam, CCcam, NewCamd, Mgcamd and NCamd. The CCcam lines I installed them in CCcam.conf. The OScam lines I installed them in Tuxbox(oscam trunk) But the lines NewCamd, Mgcamd and NCamd don't know where they go. Here are some examples of the configurations of the lines I use. CCcam Code: C: test.gottest.tv 3050 test2 test1 OScamd Code: [reader] label=test.gottest.tv protocol=osccam device=test.gottest.tv, user=3050 password=test2 group=1 ccckeepalive=1 NewCamd Code:(I don't know where to put this line in the box) [reader] label=test.gotest.tv enable=1 protocol=newcamd key=0102030405060708091011121314 device=test.gotest.tv,3056 user=test2 password=test1 group=1 inactivitytimeout=1 reconnecttimeout=30 lb_weight=100 ccckeepalive=1 MgCamd Code: (I don't know if this configuration code is correct or where to put this in the box) CWS=test.gotest.tv 3056 test2 test1 01 02 03 04 05 06 07 08 09 10 11 12 13 14 NCamd Code: (I don't know how to configure/build the code line or where to put the NCamd lines in the box) -
Code
Hello! Can someone explain to me how to configure and put MgCamd and NCamd lines in the Octagon SF8008 4K? I have the OpenATV 7.1 image installed.
