Posts by rikjaard-real

Quote from technodvl2

shame the original eaglebox was a good little box

couldn't agree more - all be it a clone dm500 - shame the makers didn't better themselves ?

Hello Atlas

what you want to do is Very possible ! i have seen many motorised and big non motorised dishes mounted in the way you describe !

Below is the type of flashing you need - perhaps not exactly but there are many available in that style
Solutions Group (UK) Plc - Webshop

Also i would use a mount like the one in the link below which theoretically can spread the weight over the roof/ceiling beams !
They attain their weight by inserting paving slabs into the squares which are made to specification to hold them
2" x 3" Non Penetrating Roof Mount Satellite or Aerial on eBay!

you can opt for any type of pole and mount once inside just depends on exactly whats best for the given situation -
i have seen steel poles mounted to roof joists/beams with bolts drilled directly through the pole and beam then secured with big self tapping nuts = 18mm

Hope this gives you an idea ! Ultimately anything is possible !

Stay cool

Rik

Quote from mutz nutz

for £55 what does anyone want lol

ideal for the bedroom/kidz or just cheap 2and box -

i tried it but it glitches ! latency / delay ? - Upon further enquiry the providers info says its not any use for online gaming ! i got ping times from 600ms +

Quote from romman

it would be a much harder task trying to hack 5kys epg software system asking for a download when you required it.

there epg is updated o t a (over the air) through a dedicated Data stream from the satellite ! i think its on 11778v 27500 fec 3/4

most technomate rxers have the ability to use this stream already -

:rikjaard1:

it could be the wireless signal format

i know i used N type over B or G - is the tenda even compatible wiv B or G - did you check what signal the 02 router is emitting ! most can be configured to select the signal type _ my bt router allows N B & G choice in the settings !

wise move trying @ home again - these things do ya head right in at times :misdoubt:

To set it up you must have it in router mode i seem to remember ?
are you are selecting client+ap mode with the little button once you have set it up in router mode ?

e

i use a tenda 150 with an eagle box that lives across the street in an old boys house - its nearly 40 meters away and connects fine !
i set it up in client+ap mode with wpa/wpa2 encryption - i followed online instructions direcct from tendras site from memory -

the eagle is set to dhcp on

Quote from spodge007

here are my configs:-

oscam.conf

[global]
nice = -1
logfile = /dev/null
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1

[webif]
httpport = 8888
httpuser =oscam
httppwd =oscam
httprefresh = 5
httphideidleclients = 0
httpallowed = 192.168.0.0 - 255.255.255.255
debug = 255

[newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000

oscam.server

[reader]
label = ***uk
protocol = smartreader
detect = cd
device = 008:003 ---> I got this by plugging my smargo usb smartcard + reader in and running the command lsusb to get the bus/dev ids
emmcache = 1,3,2
caid = 0963
boxid = xxxxxxxx ---> same boxkey I used in my old CCcam.cfg file last time I had a go at doing this!
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
mhz = 600
cardmhz = 600
ident = 0963:000000
group = 1

oscam.user

[account]
user = cccam
pwd = cccam
monlevel = 0
uniq = 0
group = 1
au = ***UK
caid = 0963

you need a user name and password in web if - or perhaps you just omitted them for the post - Sorry if thats the case But it think you need to add summit there ! i used oscam osacm as example above !

could be that Digital switch over is not completed yet for your area ! However i'd imagine that if you were using an aerial pointing at CP you should get all the channels ?
If Both Places are using relay stations you might find you have to wait until completion of DSO to receive all channels as they only do BBC transmissions on 1st stage of switch over m8 !

i would login as root and issue "top" command - then you can see which programs is running !

i think you need to set your static ip address
it can be edited in /etc/network/interfaces

should be summit like

iface eth0 inet static
address 192.168.1.100
netmask 255.255.255.0
broadcast 192.168.5.255
gateway 192.168.5.254

Manual-Howto - Debian Wiki

Quote from musogeek

Enigma2 is not ideal at setting priorities that would be useful for those of us (and that is a lot) who have one fixed sly and one motorised. What would be ideal is if you could tell it to always record on the fixed dish as a priority regardless of whether you are watching a channel on the fixed dish or motorised

Can the develpers be informed of this Quirk and perhaps make a fix in the future releases ?

easy to setup wozbwfc ! - you'll have no problems att all ! its all clearly set out along the left hand column of the routers http set up page.

Quote from Madhatter

I have a similar sort of issue with talktalk. Clients can connect but I cannot connect using my DYDNS settings, shows offline. though internal IP works though

Not sure if your problem is the same ! i'm saying i cant connect to my server remotely from my m8s virgin connection ! Not just the dreambox on the cccam port ! i cant connect back using ftp/telnet/ssh http -
i have not yet had a chance to try with my ip yet but i'm seeing him again tuesday !

i think your saying you cant connect to your server from your own house using dyndns - thats somesort of loopback problem and is normal ! for a local connection you should always use local ips instead of dyndns !

Rik

If you add TS Panel plugin you can find all the CAMS and CHANNEL lists can be downloaded from there direct to your box ! It makes life very simple !
Here have a read through the link
http://linuxsat-support.com/en…ddons-server-updates.html

Go steady

:rikjaard1:

its a netgear router i think ? doh didnt take to much notice ? i did open all the ports involved in this specific share ! both standard listen port for cccam and the outbound servers port !
cheers romman

Quote from Sandman

Not the best if ISPs are starting to become proactive with this sort of thing!

i'm certain i heard summit on the news about certain isp's had signed up to a code of conduct which obligates them to cut off persistent filesharers,although i'm sure they have to warn you first ?
i am confused at the moment - He has a protek there and thats working all ok connected to a server getting jsc sports

i thought it strange when i couldn't get to my home network via the given dyndns name which is the same as the server uses ?
took the box up the road to another friend with virgin and everything is fine ?

oki doki ! thanks for the input sandman,

has anyone had this kind of issue ?
my good friend has virgin broadband and suddenly after 6 months he cant connect !
while i am at his house i find i cant connect to to my home network via dyndns ? Does this mean Virgin is blocking something ?

i tried to connect to my server using

filezilla - ftp
putty - ssh
putty - telnet
http - firefox

each time i get timed out connection !
server is live because i can connect with 3g mobile ? internet is good as is all connections as they return websites .com.org.co.uk ect ect

Any ideas or previous experience with this issue ?