Posts by sync

Try using a different ftp program, flashfxp, filezilla etc

Any gemini image up to version 4.2 will work on any clone dm500, there is no time bomb on them.
3.6 and 4.2 are the most stable but there are no cams via the blue button, you need to add them manually.

I'm on a new build of oscam and it does the same for me so I doubt it

Sent from my iPhone using Tapatalk

What make/model box is it paired to ?

Sent from my iPhone using Tapatalk

I moved to S kype a while ago and tbh I prefer it, we got to move with the times :)

Sent from my iPhone using Tapatalk

his card = group1
your card = group2

don't forget to allow his users access to both groups

[account]
user = user
pwd = pass
caid = 0963
ident = 0963:000000
group = 1,2

Have you tried a manual scan on the exact freq ?

Did you have this card working previously in anything other than the official box ?
Give us something to go on here, configs ? have you rsa keys ?
You won't get any help unless you provide more info

What card ?
Cos if it's an 0963 card and you were getting 700ms to 1000ms then your card is overloaded big time
Then that would suggest your either a payserver or your config is rubbish !
So which is it ???

rqcs says it's DT08 so oscam is probably looking for a valid rsa or at the very least a cam_n for session negotiation
As nano has said you will probably need to use a valid rsa

btw rqcs to oscam could be a non runner, ive seen someone try and fail
rqcs runs just fine, so as asked why oscam ?

No it won't delete any other cam, I've installed CCcam 213, CCcam 214, oscam & mgcamd all on a dm500

But you should always backup your configs as well, just in case

Yes of course you can, as long as the box has enough memory

Ok oscam is seeing more of your card now but still looking for a valid rsa key

What version of rqcs are you using and can you check your rqcs.conf for a rsa key or cam_n key if you got help to set it up previously

rqcs session negotiation says the card uses DT08 method for pairing

I've stripped down some of your config a bit and made changes so try this and report back please

[global]
logfile = stdout
nice = -1
waitforcards = 0
preferlocalcards = 1
lb_save = 100
lb_retrylimit = 1600
lb_reopen_mode = 1

[newcamd]
port = 10010@1815:000000,000901,000903,000801
key = 0102030405060708091011121314
keepalive = 1
mgclient = 1

[reader]
label = bell_smargo
protocol = mouse
device = /dev/ttyUSB0
caid = 1815
boxkey = XXXXXXXXXXXXXXXX
detect = cd
mhz = 357
cardmhz = 357
ident = 1815:000000,000901,000903,000801
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-g = 1

[account]
user = living
pwd = living
group = 1
caid = 1815
ident = 1815:000000,000901,000903,000801

Post your oscam configs

That's a really old rom compared to what's around now
Your region must have a lot of older boxes that would be too expensive to replace to complete a card swap

oscam should read and share your card no problem without the rsa if rqcs does
but you will need to have everything in the correct order in the oscam config
Ill see what I can dig up for you

Interesting, what card will you be unlooping ?

Sent from my iPhone using Tapatalk

It will depend on the box your card is paired to or more importantly the method of pairing used
For the average person it would be almost impossible to do

Sent from my iPhone using Tapatalk

Not sure if it's public, but you might find something that claims to be it, some time ago the creator was paid to stop it's development......allegedly ;-)

Then add them to reset in service-map

<reset-services>232C 2333</reset-services>

And test a user with this

<user name="user" password="pass" [COLOR='#FF0000']map-exclude="false"[/COLOR] profile="myprofile"/>