Have you added you own IP address as your allowed address.
httpallowed = 85.98.2248.48 This is just an example so add you own IP address.
Have you added you own IP address as your allowed address.
httpallowed = 85.98.2248.48 This is just an example so add you own IP address.
Is there a certain config on oscam server box side for the following situation:
Cccam client cannot get a certain card from oscam server.
But switched to oscam (client and server) the channel clears ?
What is the certain card ? it would make it a lot easier to answer rather then guess ??
Did you get one ?
Still a few of the discovery channels working.
hi is not recommended to do it online maybe they change the place on the menu ??? or missing ?? I think bh is 4.2 now
Open BH is 4.2 but BH based on Original VU+ image is 3.0.8
Have you added any plugins or maybe a different skin ?
This is a quote from a member on streamboard and it would explain your problem.
quote:
11 December 2018
The SCT informs that from DECEMBER 2018 it will be necessary to replace all Viaccess cards from 5, 6, 8, 9, 11 and 12 already sold, it will need to change from the current Viaccess 5 version to the version 6 due to hacking system hacking.
The replacement methods are already operational as the new Viaccess 6
cards are available. The affected cards are:
SCT PENTA 5 CHANNELS VIACCESS, SCT ELEGANT 6 CHANNELS, SCT PLUS 8 CHANNELS VIACCESS, SCT ARABEST 9 CHANNELS, SCT 10 CHANNELS SCT FROM 12 CHANNELS
Nothing must be done for the Elìte with 16 channels or for all the other Nagravision cards.
Since this post is 'alive' and I've asked before (stagnant).
Why would you install this on a computer or router?
The purpose?
I would guess one thing is if you had a DVB card in a pc. But a router? Why?
Anyone?
Running Oscam on a redundant device makes more sense than having your server on the STB you use on a daily basis, every time your STB reboots, crashes or you decide to re-flash you take your server offline which can be annoying to some clients.
I use an old mini pc that lives in a cupboard with no screen, mouse or keyboard attached and I can monitor and run it remotely.
So you run on different IP ranges so there is no reason you should have a conflict, going back to your original post I think a virtual lan would be the solution.
What sort of router do you use ?
Do i need to rename this to .Exe
how do i setup this file :(
Unzip it with something like 7zip
Get a cheap mini pc from that auction site and a couple smargo or omnikey readers and away you go, I did it for less that than £50
The rest of the info you need is already on this forum.
Glad you are sorted.:redface:
Can you configure your router to have multiple LAN IP address's ?
Never had to repair one, I assume you have tried a different cable ? and also make sure it is clear of any fluff etc.
Green should stay one and the orange one should flicker when data is being transferred.
If you use oscam are you blocking same name ?
You use uniq to block maybe ?
This is not an issue I have heard of but sit tight, 3.0.8 is on the way which may solve your problem.
After password add group and that is all you need.
Does it connect but not decode anything ?
[reader]
label=*****.***
enable=1
protocol=newcamd
key=0102030405060708091011121314
device=*****.***,18515
user=*******
password=*******
group=1
inactivitytimeout=1 Not needed
reconnecttimeout=30 Not needed
lb_weight=100 Not needed
cccversion=2.1.2 Not needed
cccmaxhops=10 Not Needed
cccwantemu=1 Not needed
ccckeepalive=1 Not needeed
Display More
All I see is people with problems because you all over complicate things, set up a basic reader then make changes to improve it when you understand what and why you are changing things.
You have a very complex config set up, do you really need that ?
Also what caid do you have problems with ?
Have you configured your prio and ignore ?