thanks hisakatano for al, but not work powervu in my h9s, iam in northamerica, you config working very fine in a dm900 clone, but in my zgemma h9s not work.
Posts by gatonico
-
-
Thank you Hisakatano, I will probe and post results
-
root@dm900:/tmp# flash-rescue zImage-rescue-3.14-r0-dm900-xxxxxx.bin
Manufacturer ID: xx
Memory type : xx
Memory density : xx
read id ok
comparing 2844 sectors...
erasing 2842 sectors...
writing 45472 pages...
verifying 2842 sectors...
flash done
root@dm900:/tmp#
Thank you, may be that update the bootloader with most new.
Best regards
-
Many images made by monuser have this problem. Someone should do some cleaning. Monuser does not seem to understand or pretend. Monuser, do you hear us?
You are right, the image pure6.2 from monuser, work like a charm. but many others not work.
-
this imagr not boot, still red led, please fix.
Thank you
-
please check your image, because NOT boot in my dm900 with sim 2.30.
Thank you
-
Thank you, what changes from the last version of the dreamelite sim2.30 of 27-08-2018, the drivers were updated?
-
I have original bootloader. Read my experience on johnny's forum - jb8a8f8 dot com
i read, but may be load by telnet without troubles? or for what other method load?
Thank you
-
Unfortunately, from dreamboxupdate. There is no bootloader for dm900 clone. Only original. Try to read my experience with bootloader on jb8a8f8.com forum.
ok i read your experience, but only for sure, the bootloader from dreamboxupdate may be compatible in clone without problem? and how update bootloader? with telnet?
Thank you Bibic
-
thank you monuser, image woork like a charm in my dm900 sim 2.30
-
Looking mgcamd for Openatv 5.3. Is there working version?
It doesn`t work on openatv 5.3.. Its only working on blackhole, openblackhole and VTi.
too working fine on Pure2, i prove in Zgemma h9s 4k
-
This IPK .. for Zgemma H9s
and PowerVU Config Files
Config File to etc/tuxbox/config
hi hisakatano, what image you use in zgemma h9s for powervu. Thank you
-
thanks excellent work on zegema h7c
What ncam work for you zgemma? Cortex or what? Thank you
-
I very thank you for the guide on this post , I managed to get autoroll working on sat 58W in my dreambox DM 900 UHD clone
Please share the config files and softcam.key thank You in advance
-
corrupted file.
WINRAR can not open itbecause is nfi not rar, this image send directly to dm800
-
I tried. FW AZfox S4S and AZ ... Installed normally.
FW set to load properly.
When you try to configure the restarts.
This happens every time
when trying to configure anything.
it´s because you have the opènbox s16 3606q, because i have the 3606d and the bins of azmido and s4s working fine, but not difference of openbox s16 bins -
never heard of the 3606h only 3606d and 3606q.
probably a slight hardware difference between the two.the 3606d and 3606h are the same, only a little software variation, because all new updates for 3606d come in as 3606h, and the firm for azmido p22 and azfox s4s is compatible with openbox s16
-
This is a different version maincode and ID chip. There is only one chipset Ali M3606c. Maincode in firmware versions (FW) I've seen four.
There are two FW with Canel list are normally set up and working in North and South America.
Yesa you are right only one chip from alitech, but the maincode is diferentm but in the receivers that have the maincode 3606d and 3606h NOT WORKING the files 2.8.1 and 16-10 that working with maincode 3606q.Regards
-
I have not found a firm ALI specification chip IDS: 3606d and 3606h.
Tell me where did you get this information?
after maincode version, because the 10-16 and the 2.8.1 firms not work in this receivers with 3606d or 3606h, proved by meNewcamd works but much more slower than at 2.8.1
May be but is the only firmware for my Openbox s16 3606d that working fine with all newcamd providers in North American, specifically Mexico