Firmware openbox s16 20-10-2012

There are 42 replies in this Thread which was already clicked 11,578 times. The last Post () by amina001.

    Quote from gatonico

    Yesa you are right only one chip from alitech, but the maincode is diferentm but in the receivers that have the maincode 3606d and 3606h NOT WORKING the files 2.8.1 and 16-10 that working with maincode 3606q.


    Regards


    I think there are several manufacturers of receivers.
    Perhaps they in factory flashing FW receivers
    write the original version maincod in bootblock loader.
    That is why the problems with running other FW.

    Quote from lutz diagram

    never heard of the 3606h only 3606d and 3606q.
    probably a slight hardware difference between the two.


    the 3606d and 3606h are the same, only a little software variation, because all new updates for 3606d come in as 3606h, and the firm for azmido p22 and azfox s4s is compatible with openbox s16

    I have a S16 with information:
    Bootloader: 1.0.0 2011-8-11
    Maincode: S3606H-1.0.0 2012-10-20
    Seecode: M3606 SEE 2012-10-20
    Openlogo: 1.0.0 2012-3-24
    defaultdb: 1.1.0 2012-9-11
    userdb: 1.0.0 2012-10-20
    hardware 1.0.0.10
    Is my S16 using FW of this topic?


    I tried. FW AZfox S4S and AZ ... Installed normally.
    FW set to load properly.
    When you try to configure the restarts.
    This happens every time
    when trying to configure anything.

    Quote from Mitrich64

    I tried. FW AZfox S4S and AZ ... Installed normally.
    FW set to load properly.
    When you try to configure the restarts.
    This happens every time
    when trying to configure anything.


    I have the same one:


    Bootloader: 1.0.0 2011-8-11
    Maincode: S3606H-1.0.0 2012-10-20
    Seecode: M3606 SEE 2012-10-20
    Openlogo: 1.0.0 2012-3-24
    defaultdb: 1.1.0 2012-9-11
    userdb: 1.0.0 2012-10-20
    hardware 1.0.0.10


    Have you tried with AZ MIDO_20120618.abs and S4S_721s3606V3_721.abs FW?


    Regards


    Yes I installed both FW. Both do not work, as it is written in my previous post.

    Quote from Mitrich64

    I tried. FW AZfox S4S and AZ ... Installed normally.
    FW set to load properly.
    When you try to configure the restarts.
    This happens every time
    when trying to configure anything.


    it´s because you have the opènbox s16 3606q, because i have the 3606d and the bins of azmido and s4s working fine, but not difference of openbox s16 bins


    It's yours S16 working fine with AZ MIDO_20120618.abs and S4S_721s3606V3_721.abs FW?

    I am Seeking lists compatible channels for my s16. Someone tells me that channel lists can be loaded on my decoder? ALI - ferguson-120 - etc.

    sorry i have tried all firmwares but the cccam and the mgcam does not work at all. cccam is very slow and the picture is freezing.the worst recerver i haveever had -openbox s16-

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login