Posts by mkhan

Hi Ziko,

Is it possible to add English epg for all MBC channels? The source in the app is Arabic.

Can you also add Epg for the Pakistan sports channels like Geo Super, PTV Sports and Ten Sports?

I have this problem as well. I think this is due to CSP problem and is the only channel that does not clear.

I have it working on the Duo using BH image, will there be support for the Vix image?

I would like to get it going on the Tm Twin which does not have BH support therefore I'm stuck stuck with Vix.

I'm reading my UK card along with a Nagra share I'm receiving from someone else in Oscam. I'm able to view the channels from my share on a client receiver but not the Nagra share I'm receiving from some one else. In Oscam its says both as connected successfully but only my card clears.

Any ideas where I might be going wrong? I have posted my configs below.

[global]
nice = -1
WaitForCards = 1
logfile = stdout
disablelog = 0
preferlocalcards = 1
saveinithistory = 1
lb_mode = 1
lb_save = 0
lb_nbest_readers = 2
lb_nfb_readers = 1
lb_min_ecmcount = 5
lb_max_ecmcount = 500
lb_reopen_seconds = 900




[webif]
httpport = 16578
httpuser = XXXX
httppwd = XXXX
httprefresh = 10
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255




[cs357x]
serverip = 127.0.0.1 
port = 20000
keepalive = 1

[reader]
label = ***uk
protocol = internal
device = /dev/sci0
caid = 0963
detect = cd
mhz = 358
cardmhz = 357
group = 1
emmcache = 1,3,8
blockemm-unknown = 1
blockemm-u = 0
blockemm-s = 1
blockemm-g = 1
cccversion = 2.2.1







[reader]
label = remote 
protocol = newcamd 
device = @dyndns.orf  
user = XXXXX  
password = XXXXXXXX
key = 0102030405060708091011121314 
group = 2
fallback = 1
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
cccversion = 2.2.1

[account]
user = XXXXXX
pwd = XXX 
disabled = 0
group = 1
uniq = 1
sleep = 0
au = ***uk
cccmaxhops = 1
cccreshare = 0
group = 1,2

I don't have the Ident and group info in oscam.user.
I will add this info and report back.

I'm trying to share my card out to my cousin who has lost the HD package on his card so that he can reshare mine and share his SD card at the same time. When I try to put his card in the receiver and and my C line as reader in oscam.server it will only allow me to use either the original card or line and not both. He is using Oscam+cccam setup.

How can I get this working?

Oscam.server config:

[reader]
label = ***UK
protocol = internal
device = /dev/sci0
caid = 0963
detect = cd
mhz = 358
cardmhz = 357
group = 1
emmcache = 1,3,8
blockemm-unknown = 1
blockemm-u = 0
blockemm-s = 1
blockemm-g = 1
dropbadcws = 1
ecmwhitelist = 0963:3B,3E,41,42,44,45,47,50,53,5F,61,62,66,67,68,69,6A,6B,6C,6F,70,71,72,73,76,77,79,7A,7D,7E,80,82,84,85,8B,9A

[reader]
label = remote
protocol = cccam
device = XXXXXXXXXXXXX
user = XXXX
password = XXXX
caid = 0963
group = 2
cccversion = 2.2.1

Its funny how people are starting to recommend moving to *** ITalia/Germany. It would be interesting to see if these package will be made the next target by NDS in the coming months as pretty much all other NDS users such as Total TV, Dolce, Visat HD & International TV provider cards can no longer be shared.

Quote from blacksx

I'm just concerned sly will send an unwanted emm?

Its only a matter of time now till we all lose the HD/premiums and by stopping emm updates to your card should be fine until the entitlements run out. Its is up to you on how you go about it as we will all be seeing dark screens soon.

Do you need to create two separate user accounts for both the N & L line in Oscam or just one?
I enabled both protocols with two separate acounts in Oscam for both the N & L line and it would only enable camd3 protocol.

If it is possible can you explain in detail how to do it?

I've enabled both camd3 and dvbapi in oscam.conf whilst connecting to cccam via an L line and I can only use one or the other.

Is there anyway to save the emms and then write them to Oscam manually?

Will the entilements update if I enable dvbapi and set a user account to update emms and still use camd3 protocol to cccam?

I'm currently using Oscam+cccam using the newcamd protocol and would like to switch to the camd3 protocol and use an L to connect to cccam instead of an N line. However from past experience my 0963 card has not been able to receive emms from a cccam client using camd3 protocol whereas using newcamd updates the card.

Is there anything I can add to my configs to allow my card to receive emms when using the camd3 protocol?

Thanks mate, it did the trick.

My Linksys router was showing signs of ageing therefore I replaced it with a Netgear router and now I cannot seem to access webif on my Oscam+cccam setup.

I get the error message "403 Forbidden Access denied"

My webif settings:

[webif]
httpport = 15500
httpuser = *****
httppwd = *****
httprefresh = 10
httpallowed = 127.0.0.1,192.168.1.28-192.168.0.xx

what am I doing wrong, is there anything in the router settings that is preventing it from working?

If I was to change to a later version do I use the new or the old PPC file?

Which version of Oscam does this image run?

It makes a good server.

See link - OScam Anticascading - Oscam Tips

Some people have to use CCcam 213 for instance if you are running your card using Oscam+CCcam then you would use CCcam 213 with 256 trick else your clients will not see your card as local with any other version of CCcam.