I tried many different ones and it's the same on all images, isn't it wrong on all of them? it works a little better on openvision but the box does not find the module
Posts by maho33
-
-
hi my friends thanks again to everyone who helps me i think there is no fault with my box dm8000
found another same box dm8000 and they are the same error on it also tested many image it gets stuck like my box it can't be wrong on my box what could be wrong because tested on 2 dreambox? is it image-software-hardware ??? must be one of them -
this one is online but have to order it takes a long time so I'm asking about the one with 3 sticks
-
can't find the same one, I can try this one with 3 sticks
-
how do i remove it just lift or ?
-
mean this one ?
-
You can also check batter on board by multimetr how voltage is. My batter was finished (0,3V) showed) and had problems with self restarting of my DM. After replace new battery DM start working very stable.
can you send a picture of where the battery is so I can change it and test it
-
it is quite possible that a plugin is causing these crashes. Try flashing again without installing any plugins
I'll test when I get home
but there is a fan if I don't activate fan control 2 the box gets very hot
-
so there are settings on fan control 2, I have installed the fan myself and the hard disk
I have disconnected both fan and hard disk and tested it is the same error
-
can i select multiple plugins to install
or one and one
-
tried everything it's the same error ...not found module...
test many images both new and old the module works without problems but the box freezes on all images ...... without openvision image but on this one I couldn't get the module to work ..
I don't understand anything about this damn box, why does it work on openvision without problems and on the other images it gets stuck when I change the channel then I have to disconnect from the power
-
Any suggestions my friends?
those using openvision image
-
thanks but it's the same ...no module found....
damn also tried everything this damn box only works on this openvision image without problems no freezes at all
don't understand, tested many images and there is a problem with all of them without this openvision image
-
loaded it and sent to
usr/lib/enigma2/python
BoxBrandingTest.pyo
it's the same error ....no module found....
-
root@dm8000:~# opkg install /tmp/*.ipk
Installing enigma2-plugin-systemplugins-ciplushelper (5.2) on root
python: can't open file '/usr/lib/enigma2/python/BoxBrandingTest.py': [Errno 2]
No such file or directory
Removing any system startup links for ciplushelper ...
Removing any system startup links for cihelper.sh ...
Configuring enigma2-plugin-systemplugins-ciplushelper.
root@dm8000:~#
root@dm8000:~#
root@dm8000:~#
root@dm8000:~# reboot
-
has anyone managed to get the module running on openvision image
-
try to install it and you will know
Send ipk file via FTP (via DCC or FileZilla) to tmp> / var / temp
after over telnet:
opkg install /tmp/*.ipk
reboot
I have installed but still can't find any module this image works fine on the dm8000
only if I get the module running
-
I have to install something to find the module
Try the attached CiPlusHelper.
it is py3 image....does it fit
-
finally i managed to flash openvision thanks for all the help it doesn't find the CI module, I have to install something to find the module
-
tried many images because the box freezes, can't do anything until I disconnect from the power
only dreamelite and openvision image are slightly better than the others
this image can be flashed without problems ....openvision-e2-multilanguage-py2-10.2-r382-dm8000_nf .....but I couldn't get module CI to work
therefore want to test them here
openvision-e2-multilang-py2.7-12.1-r454-dm8000-20220711_flash
openvision-e2-multilang-py3.10-12.1-r454-dm8000-20220713_flash