In oscam webif, click on "config" tab then underneth that, click on anticascading, there should be a tick beside enabled.
If your unsure or need an explanation on any of the entries in the webif, just click on the text and it will open the oscam wiki relating to that entry, Eg: click on " enabled" and it will bring you
Quote[h=4]enabled[/h]
parameter is required
enabled anti-cascading:
enabled = 1 # enabled
= 0 # disabled (default)
Post up your webif configs. # out any sensitive info and we'll see if it can be sorted.
No, it will allow the user to share your line to someone else (if he puts it in a server)
Put it to 0 and he will only be able to share it within his network (from my understanding)
Anticascading may be what your looking for.
QuoteDisplay Morenumusers
parameter depends on setup/programversion
used only if anticascading is enabled!
numusers = # quantity
user per account
Example:
numusers = -1 # (global value from oscam.conf, default)
numusers = 5 # (maximal 5 user)
numusers = 0 # (anticascading disabled)
Have a look here:
http://linuxsat-support.com/view.php?pg=openatv
Or use the navbar (top of page) and click on image/firmware download tab. Most teams are there.
Is your receiver connected to your network?
Have a look in cccam info (blue button on some images), scroll down to servers, hit ok and there should be a green mark beside the server (connected). If it's red, it's not connected.
Then check to make sure cccam is running. (blue button again on some images), scroll down to softcam/softcam manager and start cccam (location varies with image).
Have a look here for them:
http://linuxsat-support.com/forumdisplay.php?f=889
Disconnect all usb attached storage etc..
Try another usb stick for flashing.
In the image folder on your stick, there is a file called "noforce".
Try renaming that file to "force" (without the "") and see if it will flash then.
Try all usb ports.
If it does flash and reboots, power it off and remove your key as it may keep reflashing since you've renamed the file.
What image did you try to upgrade?
Have you tried re-flashing the bootloader.
http://linuxsat-support.com/showthread.php?t=60555
Have a read of this thread also, it may help.
http://linuxsat-support.com/showthread.php?t=107984
You shouldn't need a second feed.
In service searching, tuner configuration, just setup tuner A (or B if you prefer)
Configuration mode = simple
Input = single
Satellite= 28.2 (scroll across to select the desired satellite)
Then scan for channels or setup autobouquets or install a channel list.
CCcam.cfg goes to /etc on vix.
They're not normally on the image but can be downloaded from the feeds (don't think they come with any configs though).
Alternatively, install our addons panel and get your required cams from there:(configs included)
http://linuxsat-support.com/attachment.php?attachmentid=43227&d=1447186593
If there is only one output from the monoblock, try enabling diseqc a/b in tuner configuration.
Configuration mode = simple
Mode = diseqc A/B
Port A = Hotbird 13.oE
Port B= 19.2 Astra.
It may work then (depending on the monoblock)
Your backup image will be in the "image backups" folder.
Open the folder up and there should be a .zip file in there.
Drag this file to your desktop and extract it out to a freshly formatted usb stick .
Insert that stick into your second zgamma and push the power button, "flash" should appear on it's display.
It should reboot when finished.
Job done.
Very good, thread closed
Have you open a port for streaming on your router?
I think the default streaming port is 8001 on most images.
You could then use the openwebif (with vlc) to view your channels (provided your upload speed is adequate)
How to install openelec on sd card is here:
http://linuxsat-support.com/showthread.php?t=74020
Install it in nand is here:
http://linuxsat-support.com/showthread.php?t=77511
Openelec builds are here:
http://linuxsat-support.com/forumdisplay.php?f=1002
Go into plugins, hit green button (download plugins) and I think it should be in system plugins or maybe extensions (autobouquets e28.2 is in one and autobouquets maker is in the other as far as I can recall).
I changed mine for the older type and have had no issues with it since.
http://www.world-of-satellite.…-Universal-Remote-Control
