Posts by codar

  • Can i use Smargo and internal card reader?

    Not too familiar with oscam/mgcamd setup to be honest.
    I only ever used oscam/cccam in the past and oscam only now.
    I only blocked the updates on nc+ card only as they are constantly been written and server was constantly "au active" on that reader (just annoyed me really)
    You should leave oscam.conf on client alright (will give you access to client oscam webif) but change your cccam port if it is the same port you use on your server, it could conflict if you ever decide to start using it as a server.
    Probably won't do any harm if you never use it as server or if you use an N-line from your server as your port will probably be different then (10001 from the above configs)


    - - - Updated - - -


    This is probably all you should need for oscam to run on your client if your line details are
    C: 192.168.0.69 12000 me metoo


    Or alternatively, install cccam on client and paste your line into cccam.cfg
    I haven't had much experience with mgcamd, sorry.

  • Getting ET8000 up and running

    Go back into autobouquets configuration and de-select/turn off "generate hd bouquets"/ select sd bouquets and allow hd swap (will swap sd channels with their available hd counterparts on free to air channels eg: bbc/itv etc.
    You can also edit any bouquet by pressing menu button while in that bouquet and move/delete any entries but if you've autobouquets scheduled to run daily/weekly these changes will be overwritten when the plugin runs again.

  • which box

    If you like blackhole images, vu is the way to go.
    I have both the duo2 and solo2 and find both very good receivers.
    The duo2 is very big in comparison to the solo2 though but is capable of housing either a 2.5 or 3.5 hdd.
    Solo2 can only accomodate a 2.5 hdd.
    Also, the duo2 has pluggable tuners (can accommodate up to 4 tuners) where as the solo2 only has two onboard non interchangeable satellite tuners.
    Duo2 has 1gb flash, 2gb ram, two front displays and 1300mhz dual core mips processor
    Solo2 has 256 flash, 1gb ram, one front vfd and 1300mhz mips processor
    Other specs are more or less the same.
    Performance wise, both are very capable and support is widespread from most image teams.
    If you require a mix and match of tuners, the duo2 is the one (although the solo2 is very capable of running usb tuners)
    It will all come down to budget at the end of the day.
    http://www.world-of-satellite.…-Linux-Satellite-Receiver
    http://www.world-of-satellite.…-Linux-Satellite-Receiver

  • Can i use Smargo and internal card reader?

    If these configs are from your client box, the most important entry is your proxy reader (oscam.server/ your line from your server) which looks ok.
    I don't think you need to create a user account/dvbapi unless you also want to run a server from this box or have a card installed in this receiver.
    Au should be enabled in your server , on your client's user account, not in your client box (unless your using this box as a server and have another client connected with these credentials).
    I'd change cccam port entry also (although not really required if it is only a client) if it is the same port as your server, they may conflict.


    - - - Updated - - -


    Your user account for this client box should look something like this in your server:


    - - - Updated - - -


    These are my configs for nc+ card in my server, (ubuntu) which work ok.


    You may need to change the protocol entry to reflect the type of reader you use (pcsc is for my omnikey) and also the device if you have more than one reader attached.
    Also change the

    Quote

    cardmhz = 2700


    If it is your receiver your running as a server
    I block everything until a month before entitlements run out then enable them to update card.
    Only takes a few mins to update it.


    Only after seeing masterg 'configs.
    Go with them for your server as mine are based on them, only modified to run in ubuntu.

  • VU Booting issue

    Have a look in your av settings (hdmi-scart etc) and i'd try an old fashioned scart lead/cinch/phono connection to see if a picture is generated.
    An unusual problem to be honest.

  • Little help with Oscam/CCcam config?

    These configs should get you started.


    Oscam.conf


    oscam server


    oscam user


    Line for dreambox:
    C: server-ip 16001 dreambox passwd
    This should update your card from your dreambox


    Fill in your own preferences for all marked in red.


    - - - Updated - - -


    Then have a read here about blocking requests that your local can't clear:

  • Duo2 tuner questions

    Quote

    there is in fact 3 tuner slots


    I assumed there was scope also to include another tuner so I purchased a dual module.
    It is only a "blank", nothing corresponding to a connection on the motherboard behind it.
    If any of ye are looking for a single dvb-s/s2 tuner module, gimme a shout as I have a spare and doubt i'll use it.
    Think they will fit uno/ultimo also.

  • Openatv5.0 image backup

    Oscam is already installed on this backup.

    Quote


    Oscam ip of wetek:8888 usr=root passwd=oscam. Just add a reader in oscam.server file


    Post #1


    - - - Updated - - -


    Use this handy tool to convert a line to a reader:

  • Problème flash Solo 2 OpenPli

    Quote

    Hello,
    I flashed the OpelPLI SOLO2 4.0 and I do not have French channels ( messages: Failed agreement or No service found no SID found in PAT )
    What would be the problem?
    Thank you in advance


    After flashing you'll have to set up your tuners. (service searching-tuner configuration)
    Then you will have to either scan in your channels (automatic search) or install a channel list.
    Channel lists can be found here.
    http://linuxsat-support.com/forumdisplay.php?f=17
    They can also be downloaded from our addons panel.
    http://linuxsat-support.com/showthread.php?t=30475


    - - - Updated - - -


    Also, please post in English.