Posts by Bean

If I restart oscam with my build it starts fine. If I restart it with the build you provided I get and error - error while loading shared libraries: libpcsclite.so.1: cannot open shared object file: no such file or directory. I have reverted back to version r9784

The card reader looks to be running fine in oscam webif

I copied your opensc.conf to /etc/opensc/ and did a restart.

I then ran the following command - opensc-tool list-readers, -l

No smart card readers found.

My opensc.conf file is located in /etc/opensc/

Is this ok?

Edit: Sorry my bad read it incorrectly!! Sorry!!

Do I remove all the #'s from # CT-API module configuration & # The following section shows definitions for PC/SC readers??

Like so -

# CT-API module configuration.
reader_driver ctapi {
module /usr/local/towitoko/lib/libtowitoko.so {
CT-API ports:
0..3 COM1..4
4 Printer
5 Modem
6..7 LPT1..2
ports = 0;
}
}

# The following section shows definitions for PC/SC readers.
reader_driver pcsc {
# Limit command and response sizes.
# Default: n/a
max_send_size = 255;
max_recv_size = 256;
#
# Connect to reader in exclusive mode?
# Default: false
connect_exclusive = true;
#
# What to do when disconnecting from a card (SCardDisconnect)
# Valid values: leave, reset, unpower.
# Default: reset
disconnect_action = unpower;
#
# What to do at the end of a transaction (SCardEndTransaction)
# Valid values: leave, reset, unpower.
# Default: leave
transaction_end_action = reset;
#
# What to do when reconnection to a card (SCardReconnect)
# Valid values: leave, reset, unpower.
# Note that this affects only the internal reconnect (after a SCARD_W_RESET_CARD).
# A forced reset via sc_reset() always does a full powerup.
# Default: leave
reconnect_action = reset;
#
# Enable pinpad if detected (PC/SC v2.0.2 Part 10)
# Default: true
enable_pinpad = false;
#
# Use specific pcsc provider.
# Default: libpcsclite.so.1
provider_library = libpcsclite.so.1
}

Yes. Omnikey reader.

Edit : HID Omnikey 3021

When I copy over your oscam file and try to restart it I am getting the following error - error while loading shared libraries: libpcsclite.so.1: cannot open shared object file: no such file or directory

Doesn't update for me though. I thought I had it sorted last week by putting it back in my thompson box but some of the entitlements didn't update and after a day or so all went. I had to put it back in the box again and ring them.

Is there any possible way you could help me to get it to update automatically?

I am currently using OSCam r9784

I must have copied and pasted the 8917 bit from somewhere. Will this version work for entitlements?

Is it possible to revert back to an older working version?

Also I have removed the CWS lines from cccam.cfg. I have the following in newcamd.list -

CWS = (Server IP) (Server Listen Port) user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

The following is my configs.

oscam.user -

# oscam.user generated automatically by Streamboard OSCAM 1.20-unstable_svn SVN r8917
# Read more: http://www.streamboard.tv/svn/…on/doc/txt/oscam.user.txt

[account]
user = xxxxxxxxx
pwd = xxxxxxxxxxxxx
caid = 0963
au = ***uk
group = 1

[account]
description = mgcamd1
user = user1
pwd = password1
group = 1
keepalive = 1

[account]
description = mgcamd2
user = user2
pwd = password2
group = 1
keepalive = 1

cccam.cfg -

SERVER LISTEN PORT : XXXXX
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME :xxxxxx
WEBINFO PASSWORD :xxxxxxxxxx
TELNETINFO USERNAME :xxxxxx
TELNETINFO PASSWORD :xxxxxxxxxx
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 16001
ZAP OSD TIME :0
OSD USERNAME :xxxxxx
OSD PASSWORD :xxxxxxxxxx
OSD PORT :80
SHOW TIMING : yes
DEBUG : yes
NEWCAMD CONF : no
#DISABLE EMM : yes
#EXTRA EMM LEVEL : yes
SHOW EXTENEDED CLIENT INFO : yes
MINI OSD : no
#MINIMUM DOWNHOPS: 1
CHANNELINFO FILE : /var/etc/CCcam.channelinfo
PROVIDERINFO FILE : /var/etc/CCcam.providers
CAID PRIO FILE : /var/etc/CCcam.prio
LOG WARNINGS : /var/log/warnings.txt
SOFTKEY FILE : /var/keys/SoftCam.Key
AUTOROLL FILE : /var/keys/AutoRoll.Key
#STATIC CW FILE : /var/keys/constant.cw
#BOXKEY: /dev/sci0 XX XX XX XX
#SMARTCARD CLOCK FREQUENCY: /dev/sci0 6800000

N: 127.0.0.1 10001 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

CWS = xxxxxxxxxxxxxxxxx.dyndns.org 10001 user1 password1 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS = xxxxxxxxxxxxxxxxx.dyndns.org 10001 user2 password2 01 02 03 04 05 06 07 08 09 10 11 12 13 14

F: dream1 dreampass1 1 0 0 { 0:0:1 }

newcamd.list -

CWS = xxxxxxxxxxxxxxxxxx.dyndns.org (server_listen_port) user1 password1 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Channels not working, any ideas? Most likely have something wrong.

Hi Guys,

I have acquired a couple of ***box f5s's (chinese) which as far as I can make out can only run with mgcamd. I have tried several times to add clines but it seems to only want to run with mgcamd lines. Is this correct?

I would like to have mgcamd running on my server also. Would this interfere with my current cccam/oscam setup in any way? I only want to use mgcamd for certain boxes.

If this is possible could someone point me in the right direction to install mgcamd on my ubuntu server and also how to setup lines.

Bean

Sorry forgot to say VU+ Solo2

Quote from cazuela

Depends on a lot of things ,,small details like ,
what image and version you are using ,which STB are you trying to obtain it on,
have you tried the fix, etc, etc...
what you have tried so far and what you haven´t according to other threads on same subject....

Thanks for the reply.

I thought I should keep this thread separate as I think this is a different error?

My current image is from Linuxsat-Support - Blackhole 2.0.8

Not sure what "the fix" is?

Hi Guys,

My OnDemand works fine for RTE and 3Player but BBC iPlayer gives a green screen and ITV Player tells me that there are no episodes available. I don't think this has anything to do with being in Ireland as I think I would receive some on screen messages regarding this if it was working properly? Correct?

Thanks,

Bean

Quote from pheonix

We added a DNS input section into the plugin so you can add your own, in light of Tunlr closing down its servers (Tunlr is what we used to use with OnDemand but alas there are sadly no other good free alternatives).

Hi Pheonix,

I have created an account with unblock-us. I have asked them for a little support but they don't support VU+ boxes.

Would you have any experience of something similar or could you point me in the right direction?

Thanks,

Bean

Hi lads,

Can anyone tell me if I can get OnDemand to work with this image on this box and if so can anyone supply the correct .ipk file please?

Have it on my VU+ Solo2 but would like to get it running on this also if I can.

Thanks,

Bean

Hi guys,

I have a vu+ solo2 with ondemand. Rte and 3player working great but BBC and ITV geo locked.

Is there any way of simply tricking my modem that it is in the UK to allow these to work or is there a plugin available to do this on the box itself?

Thanks,

Bean

Excellent tutorial. Went without a hitch.

Thanks guys.

Hi guys,

I have got my hands on a VU+ Solo2 clone but the original image was acting up. I am looking to flash it so would anyone recommend a nice stable image which would include cccam and that I can run On Demand with also?

Thanks,

Bean

Hi,

I have a different problem if someone could help.

The last couple of mornings when this new image is booting it gets stuck and has to be powered off a couple of times for it to complete successfully.

Any ideas?

Bean