Posts by jokal

  • Amiko Alien 2 stuck on boot

    Hi,
    many thanks for your info, no i have installed 1.2.51 with u-boot update for E2, after i update only the App from a usb-Stick to 1.2.65, how can i start E2 now?
    Should i update U-Boot again?
    Many thanks
    jokal

  • Instructions for the emergency: uboot new flashing alien1

    Hi ,
    i have this problem:
    Board: STx7105-PDK [32-bit mode]



    U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock


    DRAM: 256 MiB
    Panel: VFD
    NAND: Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    512 MiB
    SPI: ERROR: Unknown SPI Device detected, devid = 0x01, 0x02, 0x14
    ERROR: Offset out of range (max=0xffffffff)
    In: serial
    Out: serial
    Err: serial
    Ident ic exist
    Ident ic get stb id
    IdentID : 0c 00 0a 00 00 11 bb
    PDK7105>


    when i boot the Box, what shall i do to solve this problem?
    Many thanks for replay.

  • Amiko Alien 2 stuck on boot

    Quote from Lavatronics

    I would do neither and contact your supplier to cure this problem for you however if you do have a go yourself then you MUST make sure once you get Spark to boot that you do an online update to Spark 1.2.51 E2 as this is the ONLY Spark update which contains a U-boot update which if you don't do you run the risk of never being able to boot to E2 again. AGAIN WE ASK THAT NONE OF OUR OWN CUSTOMERS EVER TRY THIS simply contact us if you have a problem such as this and we will look at recovering this for you.


    Many thanks for your Message, it does help me a lot.

  • Amiko Alien 2 Doesn't boot after 1.2.51 upgrade for Enigma2.

    Hi All,
    i hope that someone can help me to solve this problem.
    I'm new in this world of flashing Receiver, but i try to forst the web to do this my self. But without your help i thins it will take some days more then planned ;-)
    I have a receiver Amiko Alien 2 and i wont to install E2 with my C-lines. After Flashing the Box, it displa only "Boot" in the Box-display nothing goes to run.
    In the Putty panel, i can see the the Environment for the U-Boot are damaged?!
    U-Boot says:


    Board: STx7105-PDK [32-bit mode]



    U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock


    DRAM: 256 MiB
    Panel: VFD
    NAND: Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    512 MiB
    SPI: ERROR: Unknown SPI Device detected, devid = 0x01, 0x02, 0x14
    ERROR: Offset out of range (max=0xffffffff)
    In: serial
    Out: serial
    Err: serial
    Ident ic exist
    Ident ic get stb id
    IdentID : 0c 00 0a 00 00 11 bb
    PDK7105>




    thats all.
    I need any help or suggestion.
    Sory for my English.
    Jokal