Posts by chris130367

  • V8s Openbox Wifi issue

    Ok so problem solved, just in case anyone else has the same issue. I stubbornly thought the wifi aerial i was using was okay and it must be a box problem, even though the aerial had worked on my older box it coincidentally had obviously developed a fault. I borrowed another wifi aerial from a friend and hey presto it worked first time absolutely fine. I previously used the wifi aerial which was a (Skybox/openbox aerial) on an Nbox 5800sx up until the box died I'm now wondering if the aerial which was plugged in at the time had somehow been affected by the box perhaps a power surge or something. It just seemed strange how the V8s openbox indicated that it had found the wifi and that it was on but just not showing any AP's that's what threw me initially but just when you rule the one thing out that you think it can't possible be it turns out it was that after all. Just goes to show always keep an open mind and double check everything including changing hardware where possible.

  • V8s Openbox Wifi issue

    So by no means a newbie, just bought an Openbox V8s box but for some reason the Wifi is just not working correctly i'm thinking it's actually a faulty box. The wifi aerial I have is absolutely the correct one, I've activated the wifi and get the message that its has been found and it is on. However when I click on the Wifi Manager it is not listing or finding any AP's, well tell a fib it did briefly once after several times turning the box off and on and resetting the router it listed them and allowed me to select my router and connect but then immediately dropped the connection and the list of AP's disappeared again and no matter what i've tried cannot get them to come back up again.


    Any ideas anyone? thanks in advance.:62:

  • Black Hole 3.0 Vu+ Solo 4K UK Ready Backup By master G

    Ok thanks for that :-) I should have spotted that one myself feeling a little stupid, However there appears to be a problem with the Wifi setup the Namesever IP keeps resetting itself back to 0.0.0.0 it is not saving or storing permanently is there a fix for this? Is anyone else having this issue?


    Many Many Thanks

  • Black Hole 3.0 Vu+ Solo 4K UK Ready Backup By master G

    Ok, so double checked that it's a working line, tested on another old box and works absolutely no problem. So I have copied the log file please see below if that helps? Its a config file or something in the setup that I need to correct somewhere I think?



    - - - Updated - - -


    Whoops didn't mean to post three times my machine had a bit of a brain fart I think, and obviously I have changed the IP line to xxxxxxxserver.no-ip.biz for security :-)


    - - - Updated - - -


    Just a thought but it was an N line I converted to oscam and it uses the newcamd protocol don't know if that makes any difference?


    - - - Updated - - -


    this is my Oscam.server file with security bits xxxxED out see below:


    [reader]
    label = skyuk
    protocol = internal
    device = /dev/sci0
    cardmhz = 2700
    mhz = 450
    caid = 0960
    boxid =
    detect = cd
    group = 1
    emmcache = 1,3,2
    blockemm-unknown = 1
    blockemm-g = 1
    saveemm-u = 1
    saveemm-s = 1



    [reader]
    label=XXXXXXXXXerver.no-ip.biz
    enable=1
    protocol=newcamd
    key=0102030405060708091011121314
    device=XXXXXXXXXserver.no-ip.biz,6651
    user=123456789
    password=123456789
    group=1
    inactivitytimeout=1
    reconnecttimeout=30
    lb_weight=100
    cccversion=2.1.2
    cccmaxhops=10
    cccwantemu=1
    ccckeepalive=1

  • Black Hole 3.0 Vu+ Solo 4K UK Ready Backup By master G

    Hey Mr G, awesome image :),
    Normally have no problem getting things to run, but I'm having issues. I have placed the relevant converted file into Oscam.server but no channels :/
    Checked as much as possible placed into etc/tuxbox/config, started Oscam emu, checked inside Webif port 8888 everything is connected but still no channels. I must be missing something here any suggestions or do I need to upload a log file?
    Thanks in advance

  • Issues flashing a new image on Vu+ Solo 4K

    Anyone had any issues flashing a new image? I have the new VU+ Solo 4k and have tried to flash the Blackhole image but the box is not progressing to the flash. I have followed the instructions and no joy. I have formatted the USB to FAT32 and placed the files unrar on the stick, turned off box placed stick in front usb port and although when I turn the box back on the usb flickers to acknowledge it is being read the box simple continues to boot and goes to a channel instead of flashing the image. The only thing I haven't tried is using another usb stick as I don't have a spare at the moment. Am I missing something else perhaps?


    Thanks in advance

  • Nbox Plugin error ANY HELP?

    I have the following error and wonder if anyone knows what I need to do sort this?



    Message


    Some plugins are not available:
    Extensions/PremiumIPTV(/usr/lib/enigma2/python/Plugins/Extensions/PremiumIPTV/module_0.so: cannot
    open shared object file: No such file or directory)



    Thanks in advance