local card, shows down on CS Studio until I restart the cam

**junger** · Mar 15th 2012

Hi all VU+Duo, Oscam v6337 Ccam V2.3 sly local card, shows down on CS Studio until I restart the cam (blue button) then it clears, other peers shares seem ok, this has happened before, any ideas please

**master G** · Mar 15th 2012

Use the OscamCheck Script for Vu+ BlackHole image, works perfect.

**junger** · Mar 15th 2012

Thanks master-g, I have tried this before but just to be sure I tried it again.
FTP (OscamCheck Script for Vu+ BlackHole image) and I load it into temp, then green/yellow button, I get the error,
the screen shows
"Installing ipknew enigma2-scipt-oscam check " etc x 3.
sh: /tmp/opkg.V038rr/ipkkknew: not found
preinst script returned status 127
Collected errors
Aborting installation of ipknew enigma2-script-oscamcheck-BH
Cannot find package ipknew enigma2-script-oscamcheck-BH
execution Finished

Help please

**master G** · Mar 15th 2012

I have reuploaded the script, download and try again now.

**junger** · Mar 15th 2012

Thanks master g, that worked first time

When I use the killall command in telnet i get the following

Killall: cannot kill pid 19170: No such process
Killall: cannot kill pid 19171: No such process
Killall: cannot kill pid 19172: No such process
Killall: cannot kill pid 19174: No such process

Is this right?

Sorted thanks

**master G** · Mar 15th 2012

Quote

When I use the killall command in telnet i get the following

wait a few minutes and check var/log/oscam_restart_log.

You should get process was not working, which means the script is working and oscam was restarted.

**drfox** · Mar 15th 2012

master G I get same message as juger get
Killall: cannot kill pid 9509: No such process
Killall: cannot kill pid 9510: No such process
Killall: cannot kill pid 9511: No such process
Killall: cannot kill pid 9778: No such process
i think some wrong with this script?it kill EMU AND naver restart EMU

**master G** · Mar 15th 2012

check var/log/oscam_restart_log and what do you see ?

**drfox** · Mar 15th 2012

I can not see anything on var/log i run Oscam6059+CCcam213-S*k_UK-E2-BH do we need change on config to get oscam_restart_log???

**master G** · Mar 15th 2012

When you install this ipk make sure you do a full reboot of the system for it to take effect, then try again.

**drfox** · Mar 15th 2012

i done e2 reboot i will do it full reboot now and let you know

**master G** · Mar 15th 2012

Do a hard reset and you will see in oscam.log that script works every 5 min and write log, Enigma2 restart wont setup the cron for the script.

**drfox** · Mar 15th 2012

same message is not working killall command in telnet
Killall: cannot kill pid 9509: No such process
Killall: cannot kill pid 9510: No such process
Killall: cannot kill pid 9511: No such process
Killall: cannot kill pid 9778: No such process
and not any log file???juger please tell us how did you Sorted?? thanks

edit:is working now but take 4 to 5 minutes
and i get on oscam_restart_log this massage

Code

15/03/12 16:15 process was not working

**master G** · Mar 15th 2012

Correct, the script is set to run every 5 minutes, anything shorter than that will use too much resources on the Vu+.

**drfox** · Mar 15th 2012

thanks Mater G for all your help m8

local card, shows down on CS Studio until I restart the cam

Your support forum for satellite viewing cards and subscriptions.

Participate now!

Share

Tags