Oscam-emu Autoroll via emm ?

I have been reading a good bit on the emu grabbing and writing keys from an emm key. I have seen several setups but all examples are using a real cam. I have no actual card, just emm keys for transponders. My question is do the camid's matter? What about the dir the keys are placed into? Does oscam write the new acquired ecm key to softcam.key? What is best format for adding emm to softcam.key? For now I do have ecm keys working. Thanks

Quote from master G

You need to specify which channel will autoroll in the SoftCam>key file.. If you want it to autoroll on every channel you must add a new line for every channel.
Once you do all this, tune to the assigned autoroll channel, go to LIVE LOG in the web interface and expect to see an EMM update, it can take several minutes.

This is where Im confused. Add a new line for every channel? Does this mean add the same emm for each channel? How to do this?

Look below and please - lets start with a tp that has keys spooling constantly, that I have an emm for.

Quote from Lemme

What is best format for adding emm to softcam.key

It will be similar format to the ecm key.

Code

P 1f86 00 00010488 
P 1f86 01 00010488

But i`m not sure what the 1f86 should be.
What package is this and i can search the net for it. ?

Display More

Lets forget the 1f86 and start with a tp on sat 135w AMC10.

The tp is 4040v Epix east hd shows this on the info screen.

Video pid- 0x006e (110d)

Audio pid 0x0064 (100d)

Sid 0x012d (301d)

so would the emm key look like this for pvu?

P 012d 00 (emm key);

p 012d 01 (emm key);

If this is correct please advise how to write lines for each channel< Is it the same emm for every channel but with just changing the sid?

Thanks for all your help again. I will be helping the forum again soon...

Well I have tried adding an emm key to softcam file but the webif shows on live log key not found. Here are some screen shots. Btw the oscam configs for this setup are /etc/tuxbox/config. Btw the oscam.server file is empty. I dont see emmcache to add this

Add these to the [reader] in oscam.server:

emmcache = 2,2,2,0

saveemm-u = 1

Do I insert these lines in oscam server? Thanks

68e4037e877177049a4.png6cdb0f.pngcae764d8d642b48aee747e.png84fb7c9e285b5d4f4.png

MasterG I changed the lines in reader like shown above, now the oscam server file is like this

85e0ace016cae22986.png

I added an emm for this channel, but the emu is still looking for a key not trying to add one by emm looking at the webif keeps saying key not found. Btw I added

the emm to this format P <sid> <UA> 01 <emm key>

the sid for the channel Im working with is 0130, the emu keeps saying p0130 01 key not found.

What else can I show about the settings?

thanks

Does this look right? The group?

709d1d013745daa.png

I have loaded the above image and still getting the same message from oscam webif

e35476712cd16f63.png

Does the softcam file need more than the Emm key for the emu to try and write the key.

I have tried these formats for the emm key , are these formats correct?

P 0130 0053xxxx 0E84xxxxxxxxxx

Thanks

Changed key format to include group id, posted dummy keys and emm with same group id but still not seeing the SEND! cmd in the webif log. However I did see emm key found and shows the UA or I would post the screen shot of that here. After I changed key formats I reset oscam and all I see now is the same as screenshot above.

Changing the groupid and waiting a little longer the emu finally grabbed the spooled key and added the new key to key file. What confused me is I was looking for the

SEND! from the emu waiting to grab the key. Instead it just kept saying key not found until it finally spooled.

If I assign the same groupid to the same channels on a single tp will the emu write the key out for every channel in the same group? Or do I have to write the emm out for each channel?

Nevermind the emu writes keys for all ch for the assigned group. Thanks for your help MasterG its really appreciated.