The LATEST OSCAM-EMU FOR VARIOUS PLATFORMS Discussion and Request Thread
-
- Various Support
- elton74
- Thread is marked as Resolved.
-
-
Hello liaqatali88
My oscam.ccache file does not have that line "0B00:000000".
Already put. But on the same line, there is nothing else?
Thanks.
-
Check here my config file and give the right Attribute values to your files into your config folder and see if this helps.5cbcd46be571.jpg
-
Hi anestis1956.
Thanks.
I've corrected the file attributes.
I removed from this /etc/tuxbox/config folder the files that are not in the uploaded image (constant.cw + oscam.options + oscam.services + oscam.servid2).
I'm sending, an attachment with the header of my oscam.server.
I'm going to test this, during the afternoon.
Hugs.
-
hello you need to global config to put these file and digitalb reader file in your oscam global config file in reader file you can find on this forums and try gain
-
Hi liaqatali88.
I don't know what "digitalb reader" is.
I don't even know what this plugin does.
I don't have a card from any provider or service.
Can you give me a clarification?
Thank you very much.
-
Melgas, no extra files needed for dititalb to clear, it is up to how good your server is,
my server is OK with it and I did not know about it!
Thanks to liaqatali88 I checked and found out that it's clear!
As about your oscam.server file I must tell you I 've never seen a similar one so far!
Compare it with mine and you will be surprised!
I do not have any emulator reader at all!
The emulator works by its own, without any configuration as long as there is a SoftCam.Key file in the oscam-emu config folder.
-
Hi fellows
Asking what would be the bare minimum config file set to use pv, biss, and tandberg?
No cards, no sharing. Nothing but what's listed.
When getting a new oscam-emu binary or installing the ipk form different guys like Mohamad and Levi, etc. there are config files written to tuxbox that are confusing as hell to decypher.
Also do I need any other readers listed in the webif besides emulator? Or do I need constant cw also?
Anyone? -
Hello, I am interested in which OSCAM emulator works best for Viper Combo OS Openatv 7.0 ver
And how to delete OSCAM installed because in Add-ons is not
-
Hi anestis1956.
Thank you for the informations.
Corrected the oscam.server file, as sent.
I'll try.
Hugs.
-
Hi fellows
Asking what would be the bare minimum config file set to use pv, biss, and tandberg?
No cards, no sharing. Nothing but what's listed.
When getting a new oscam-emu binary or installing the ipk form different guys like Mohamad and Levi, etc. there are config files written to tuxbox that are confusing as hell to decypher.
Also do I need any other readers listed in the webif besides emulator? Or do I need constant cw also?
Anyone?No seriously guys. Come on. For the above do I really need all of this crap in my configs like:
ident = 0500:000000,007400,007800,021110,023800;0604:000000;090F:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000;4AE1:000011,000014,0000FE.
I have a slight clue i might just need 0E00:000000 and 2600:000000. But what the hell!
Because trying to learn what is needed and what isn't and what they mean and how to write the config for them is kind of like getting real drunk and trying to read Chinese. And stuff like this is splattered all over the different config files. -
Hi fellows
Asking what would be the bare minimum config file set to use pv, biss, and tandberg?
No cards, no sharing. Nothing but what's listed.
When getting a new oscam-emu binary or installing the ipk form different guys like Mohamad and Levi, etc. there are config files written to tuxbox that are confusing as hell to decypher.
Also do I need any other readers listed in the webif besides emulator? Or do I need constant cw also?
Anyone?No seriously guys. Come on. For the above do I really need all of this crap in my configs like:
ident = 0500:000000,007400,007800,021110,023800;0604:000000;090F:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000;4AE1:000011,000014,0000FE.
I have a slight clue i might just need 0E00:000000 and 2600:000000. But what the hell!
Because trying to learn what is needed and what isn't and what they mean and how to write the config for them is kind of like getting real drunk and trying to read Chinese. And stuff like this is splattered all over the different config files.But that is the beauty of oscam, it is so configurable. No one config will work for everyone, simple as.
Oscam will even make the reader for you,.... but in your case the only reader you actually need is the emulator
To answer your specific question about indent, then the wiki tells you
ident
Attention: If in oscam.conf [global] loadbalancing is enabled among lb_mode, then there may be no entries!
This parameter is only used for EMM and then it is not used for ECM. So you cannot force ECM to be sent to the card using this parameter.
define CAID and ident SC specific for reader:
Codeident = <CAID>:<ident>[,ident]...[;<CAID>:<ident>[,ident]...]... Example ident = # 0100:123456,234567;0200:345678,456789 = # [blank] no definition (default)
Now..... from my configs i have been using for years, these are the caids the emulator reader is decoding
and these are the indents
Code0500:000000,007400,007800,021110,023800;0604:000000;090F:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000;4AE1:000011,000014,0000FE
Do you need all / any of these?, NO....they are optional.
I have seen a lot of configs posted in this thread that are wrong, BUT they are wrong (in most cases) because they do no fit what i do with oscam
I could happily post my configs, some may find them helpful, others may think they are shite.... because as said, it depends what you want to do.
There is another part of the emulator reader, that enables keys to update
AU Providers
So to summarise, this is the emulator reader im using
Code[reader] label = emulator protocol = emu device = emulator caid = 0500,0604,090F,0E00,1010,1801,2600,2602,2610,4AE1 detect = cd ident = 0500:000000,007400,007800,021110,023800;0604:000000;090F:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000;4AE1:000011,000014,0000FE group = 6 emmcache = 2,1,2,1 emu_auproviders = 0604:010200;0E00:000000;1010:000000;2610:000000;4AE1:000011,000014,0000FE
It decodes biss, powervu and tandburg with the correct keys (and in theory biss2 and others with the keys - that are not obtainable at present)
And AU works for powerVU
Code2021/12/17 10:43:59 31F301D0 r (emu) Key written: P 00050C84 01 A9EA7A05FCE3FE 2021/12/17 10:43:59 31F301D0 r (emu) Writing key file: /etc/tuxbox/config/oscam-emu/SoftCam.Key 2021/12/17 10:43:59 31F301D0 r (emu) Key written: P 00050C85 01 A9EA7A05FCE3FE 2021/12/17 10:43:59 31F301D0 r (emu) Key found in EMM: P 0005**** 01 A9EA7A05FCE3FE ; UA: 0053C199
-
Thanks Jens. The most east I can aim at is around 40W from here. Pv, biss, tb, and a few others are the only ones used. .That said. I'll never slide a card in. Or connect to a server. Just trying to grab what comes from the sky. At this point in my 'journey' it's kind of like entering a university in mid term with little or no smarts of the course.
Plus because recent oscam changes needing a new install. I get 14 readers when I only used to need emulator. And not so sure constant.cw reader is even needed. If so, it is non present in Mohamads recent release on an aarch64 receiver. Or if dvbpi is needed and how it interacts.
If going back to the beginning with a blank slate and working on pv only. 0E00 seems to be one of the target subjects and learning how all of the other config entries work with it. I know. I'm dumb. -
some peeps use a legit card to view paid for TV on our e2 boxes, because they are.... or at least were 15 years ago, far better the the providers STB
That is what oscam is for primarily, and probably all the other readers your seeing
If all you need is the emulator, delete the others, then move to some experiments and post your findings
-
The thing is. Oscam packages come with everything and more. So to backtrack to the beginning and use values that are needed to only make pv work. then move on to biss. Kind of what I'd like to achieve. Since we've been conversing my keys file got extremely big. Some very old keys once deleted no longer clear channels. Where having a backup file comes in real handy.
-
total tv 16E not working oscam11704-emu any one help me
-
It is down on all cccam servers.
-
thank you for help me
-
Hi ;
I want to run BISS keys with the TVheadend program, but I could not run it. It works with the SoftCam Key file. I enter BISS Keys manually and cannot run it.
I would be very grateful if you could assist me in this matter.
Code
Display More2021-12-19 19:06:20.068 [ INFO] capmt: OSCam active 2021-12-19 19:06:20.068 [ INFO] descrambler: adding CAID 2600/FFFF as ConstCW interval 10000ms pc 20 ep default (BISS) 2021-12-19 19:06:20.068 [ INFO] descrambler: adding CAID 0E00/FFFF as MultiPID interval 1000ms pc 2 ep default (PowerVu) 2021-12-19 19:06:20.069 [ INFO] capmt: OSCam: mode 5 connected to 127.0.0.1:9000 (single) 2021-12-19 19:06:20.070 [ INFO] capmt: OSCam: Connected to server 'OSCam v1.20_svn, build r11704-798 (x86_64-linux-gnu); e1 2021/12/19 19:30:36 5FE571DC c (dvbapi) Demuxer 1 restarting decoding requests after 0 ms with 1 enabled and 0 disabled ecmpids! 2021/12/19 19:30:36 5FE571DC c (dvbapi) Demuxer 1 trying to descramble PID 0 CAID 2600 PROVID 000000 ECMPID 1FFF ANY CHID PMTPID 0BC3 VPID 0BC4 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 8946D7E9 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 13EF013E 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 012D0BC6 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 012D0BC5 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 012D0BC4 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 012D0BC3 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F 012D1FFF 2021/12/19 19:30:36 0328EBB5 r (emu) Key not found: F A11FEED5 2021/12/19 19:30:36 0328EBB5 r (emu) Example key based on universal hash: F 8946D7E9 00000000 XXXXXXXXXXXXXXXX ; av:3 pmt:0000 sid:0000 added: 2021-12-19 @ 19:30 2021/12/19 19:30:36 0328EBB5 r (emu) ECM failed: Key not found 2021/12/19 19:30:36 5FE571DC c (ecm) dvbapi (2600@000000/0000/012D/15:C981E100F84AC7420B98B8D5C75FBDA0): not found (1 ms) by SoftCam.Keys - AD Sports 3 HD (lg) 2021/12/19 19:30:36 5FE571DC c (dvbapi) Demuxer 1 restarting decoding requests after 0 ms with 1 enabled and 0 disabled ecmpids! 2021-12-19 19:36:11.679 [WARNING] tbl-pass: pass-eit: -: invalid checksum (len 3075, errors 9) 2021-12-19 19:36:14.421 [WARNING] tbl-pass: pass-sdt: -: invalid checksum (len 314, errors 3) 2021-12-19 19:36:15.020 [WARNING] tbl-pass: pass-pat: -: invalid checksum (len 3, errors 48) 2021-12-19 19:36:47.467 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD Transport error indicator (total 2847) 2021-12-19 19:36:47.467 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD: H264 @ #3012 Continuity counter error (total 2144) 2021-12-19 19:36:47.570 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD: MPEG2AUDIO @ #3014 Continuity counter error (total 367) 2021-12-19 19:36:47.622 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD: MPEG2AUDIO @ #3013 Continuity counter error (total 257) 2021-12-19 19:36:47.762 [WARNING] tbl-pass: pass-pat: -: invalid checksum (len 4098, errors 49) 2021-12-19 19:36:58.777 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD Transport error indicator (total 2940) 2021-12-19 19:36:58.777 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD: H264 @ #3012 Continuity counter error (total 2226) 2021-12-19 19:36:58.799 [WARNING] TS: 13E : Eutelsat Hot Bird /11747H/AD Sports 3 HD: MPEG2AUDIO @ #3014 Continuity counter error (total 378)
-
It is down on all cccam servers.
and what about oscam? if not working on cccam there is no chance to work on oscam as well. Maybe they paired their stb with cards
OSCam-EMU Support Forum
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!