Explained how to install Enigma2 Image on the external flash by Plugin Image Manager in Devices Spark

Hi everyone, I'd like to try installing an e2 image on an external USB drive following this guide (I have a Fulen 7162 aka Amiko Alien2 Triple+). I've never tried it before, and after seeing this guide, I had some doubts. Once I've followed the entire procedure and launched the e2 image from the USB, how do I revert to the default internal one? I currently have an HDMU. Is it enough to remove the USB drive and boot normally, or does it crash by constantly searching for the system to boot from the USB drive? Does this procedure affect the bootloader and the internal flash drive, or is it completely harmless? Thanks to anyone who answers.

Quote from ahmed gazye

Are you sure that you are installing the versions for your device, the 7162 processor?

First, try the solution in my topic at the following link

Thread

Solving the problem in Neutrino image after installing by plugin imagemanager

Do not look for the truth in people - but look for the truthful


Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash








Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash




Solving the problem of the appearance of an error message when tweaking…

ahmed gazye

Nov 18th 2018

If the problem is not solved, I think that the problem is in the external flash drive or in its partition.

Replace the external flash drive with another one and re-partition it in the correct way You did not mention the name of the Enigma version on the internal flash drive through which you installation on external flash drive.

Display More

Quote from ahmed gazye

Quote from jhonny82

Code

Hi everyone, I'd like to try installing an e2 image on an external USB drive following this guide (I have a Fulen 7162 aka Amiko Alien2 Triple+). I've never tried it before, and after seeing this guide, I had some doubts. Once I've followed the entire procedure and launched the e2 image from the USB, how do I revert to the default internal one? I currently have an HDMU. Is it enough to remove the USB drive and boot normally, or does it crash by constantly searching for the system to boot from the USB drive? Does this procedure affect the bootloader and the internal flash drive, or is it completely harmless? Thanks to anyone who answers.

Quote from ahmed gazye

Are you sure that you are installing the versions for your device, the 7162 processor?

First, try the solution in my topic at the following link

Thread

Solving the problem in Neutrino image after installing by plugin imagemanager

Do not look for the truth in people - but look for the truthful


Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash








Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash




Solving the problem of the appearance of an error message when tweaking…

ahmed gazye

Nov 18th 2018

If the problem is not solved, I think that the problem is in the external flash drive or in its partition.

Replace the external flash drive with another one and re-partition it in the correct way You did not mention the name of the Enigma version on the internal flash drive through which you installation on external flash drive.

Display More

Display More

Refer to my topic in the forum at the following link

Thread

​DuckBA-E2-plugin to Return​ For Spark system from​ enigma2​​ system​

DuckBA-E2-plugin to Return For Spark system from enigma2 system




There are two ways to return to the Spark system from enigma2 system



The usual way

Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and

open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears Click Ok wait a little…

ahmed gazye

Apr 13th 2020

There are no problems following either method

Display More

Thanks for your reply. Yes, I already know how to do this (select between SPARK internal and E2 system internal with OK and arrows button keys). But my question is different. If I run the entire procedure with imagemanager_2.5.5_sh4 on HDMU (on E2 internal flash) to be able to test, for example, TITAN image on USB, once the new image has been booted from USB, how do I then return to HDMU (E2 internal flash)? Is it enough to simply turn off, remove the USB stick and boot normally on E2? Thanks

Quote from ahmed gazye

Quote from jhonny82

Code

Hi everyone, I'd like to try installing an e2 image on an external USB drive following this guide (I have a Fulen 7162 aka Amiko Alien2 Triple+). I've never tried it before, and after seeing this guide, I had some doubts. Once I've followed the entire procedure and launched the e2 image from the USB, how do I revert to the default internal one? I currently have an HDMU. Is it enough to remove the USB drive and boot normally, or does it crash by constantly searching for the system to boot from the USB drive? Does this procedure affect the bootloader and the internal flash drive, or is it completely harmless? Thanks to anyone who answers.

Quote from ahmed gazye

Are you sure that you are installing the versions for your device, the 7162 processor?

First, try the solution in my topic at the following link

Thread

Solving the problem in Neutrino image after installing by plugin imagemanager

Do not look for the truth in people - but look for the truthful


Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash








Solving the problem of the appearance of an error message when tweaking the version Neutrino by the Duckba-E2 after the installation of the plugin imagemanager on the external flash




Solving the problem of the appearance of an error message when tweaking…

ahmed gazye

Nov 18th 2018

If the problem is not solved, I think that the problem is in the external flash drive or in its partition.

Replace the external flash drive with another one and re-partition it in the correct way You did not mention the name of the Enigma version on the internal flash drive through which you installation on external flash drive.

Display More

Display More

Refer to my topic in the forum at the following link

Thread

​DuckBA-E2-plugin to Return​ For Spark system from​ enigma2​​ system​

DuckBA-E2-plugin to Return For Spark system from enigma2 system




There are two ways to return to the Spark system from enigma2 system



The usual way

Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and

open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears Click Ok wait a little…

ahmed gazye

Apr 13th 2020

There are no problems following either method

Display More

I tried to install on external image same images that i have (HDMU_17208) Installation on usb (sda2 from sda1) fine but when i selected image from Image Manager and press OK the box freeze and stuck until i toggle power cord or set to off. Why?