1-Use ncam v10.9 and do this config ... then see what happens and send ncam.log
2- Test the file in attach and also send ncam.log
There are 1,706 replies in this Thread which was already clicked 417,048 times. The last Post () by protomaster.
1-Use ncam v10.9 and do this config ... then see what happens and send ncam.log
2- Test the file in attach and also send ncam.log
Display More1-Use ncam v10.9 and do this config ... then see what happens and send ncam.log
2- Test the file in attach and also send ncam.log
I have used the configuration changes you asked to me and nothing new.
Secondly, when I replace the bin downloded through ipk, with ncam.cortexa9hf-vfp-neon-Openssl-1 cam doesn't even start and it is not possible to obtain a log file.
Hi
ncam 10.9 doesn't open adult channels,so I should get back to my oscam
Is there a simple setting
Hi
ncam 10.9 doesn't open adult channels,so I should get back to my oscam
Is there a simple setting
Sorry ... From my side NO supported for adults service channels ...
Thank you for your concern.
(I hope master g doesn't delete this message.):eye-tongue:
I think I solved it
It works great when you delete service blocks from Ncam user
Ncam runs faster and more stable than my oscam
Thank you very much
Penso di averlo risolto
Funziona alla grande quando si eliminano i blocchi di servizio dall'utente Ncam
Ncam corre più veloce e più stabile del mio oscam
Grazie mille
you can post how you solved it. thanks.
Hello? Can someone share OSN free servers?
You device CPU is ARMv7 arch same as my DM920 ...
And on my device work just fine as I mentioned here
I am using the Zgemma H9.2h and Ncam 10.9 is working fine, although i lost some powervu channels and in some frequencies only some channels open while others fail.
Display More1-Use ncam v10.9 and do this config ... then see what happens and send ncam.log
2- Test the file in attach and also send ncam.log
Just for info this one armv7 4k and static one both work on my s905 amlogic k1plus box on coreelec.thanks
More info: all 4 armv7 binaries (ssl111) included in this thread work well on my vu+4k (pure2 image).
on vu+ solo4k,obh image, powervu dont work please give me a good config
Update ...
Ncam V11.0
26-05-2020
-introduced sharing instability side effect
-fix detect cx-aio on reinit userdb
-fix global cacheex_ecm_filter/_aio selection now work properly (bug: selectend _aio values for non patched peers)
-Add cx-aio-version detection @cccam-proto
-Add web/help option http://IP_your_device:8181/help
All files downlaod lines from first post
Display MoreUpdate ...
Ncam V11.0
Code26-05-2020 -introduced sharing instability side effect -fix detect cx-aio on reinit userdb -fix global cacheex_ecm_filter/_aio selection now work properly (bug: selectend _aio values for non patched peers) -Add cx-aio-version detection @cccam-proto -Add web/help option http://IP_your_device:8181/help
All files downlaod lines from first post
Hi @fairbird!
This time Ncam 11.0 works fine in Zgemma H9.2h 4K. Nice job!
cortexa9hf doesn’t work on image pure2 (ssl-111g).
10.9 ssl11 version work ok.
cortexa9hf doesn’t work on image pure2 (ssl-111g).
10.9 ssl11 version work ok.
P.s: No more bin for openssl1.1 (all bin files will be works on all image openssl old/new). Thus wrote @fairbird.
cortexa9hf doesn’t work on image pure2 (ssl-111g).
10.9 ssl11 version work ok.
P.s: No more bin for openssl1.1 (all bin files will be works on all image openssl old/new). Thus wrote @fairbird.
I've seen it. But for pure2 image cortexa9hf.... doesn't work on vu+uno4k receiver.
cortexa9hf doesn’t work on image pure2 (ssl-111g).
10.9 ssl11 version work ok.
P.s: No more bin for openssl1.1 (all bin files will be works on all image openssl old/new). Thus wrote @fairbird.
I've seen it. But for pure2 image cortexa9hf.... doesn't work on vu+uno4k receiver.
So you own a arm 4K box. I had the same problem with Ncam 10.9 in my arm cortexa9hf 4k box, image PURE2 . Instead, Ncam 11.0 works fine now.
cortexa9hf doesn’t work on image pure2 (ssl-111g).
10.9 ssl11 version work ok.
Please to send it manually ... If you sent it manually please delete it.
1-download and install ipk file
2-after installed do restart enigma2
3-Then from telnet give this commands and give me this result
4-Also look in /tmp directory If you find ncam.log then the emu works (please send to me the log of ncam)
Don’t have an account yet? Register yourself now and be a part of our community!