I have the Pen formatted in FAT16,
"I have the Pen" ...and what is the capacity -is the amount of memory? it should be no more than 1 Gigabyte THIS IS VERY IMPORTANT
I have the Pen formatted in FAT16,
"I have the Pen" ...and what is the capacity -is the amount of memory? it should be no more than 1 Gigabyte THIS IS VERY IMPORTANT
Display More#
Hello, dear jhon32
The cable is correct.
The connection is made correctly.
Confirmed with PUTTY.
After the connection is confirmed, the following error is obtained: FATAL ERROR - Boot 2nd image failed.
Thank you all.
Hugs.
#
try this ,install new rescue loader only via puty
1. Copy this .bin to /tmp
2. Open telnet and login (via the IP address)
(if you have no IP, then you must use the other way via Putty Serial)
3. flash-rescue /tmp/*.bin
4. Wait 3-5 minutes. Wait for DONE info!
5. Power OFF to 10 sec and power ON.
6. Done. You have new rescue loader.
Display More#
Hello, dear jhon32
The cable is correct.
The connection is made correctly.
Confirmed with PUTTY.
After the connection is confirmed, the following error is obtained: FATAL ERROR - Boot 2nd image failed.
Thank you all.
Hugs.
#
The problem I see here is that he doesnt have access to the login into the box, so he will never login amd be able to send the new rescue bin
We never know... some people by mistake use older PSU like for DM800se at 3 Amp... just check to be sure you use the genuine PSU if the DM900UHD that is 5 Amp.
Emo
#
Hello, dear @ jhon32
I tried the file you sent.
But the Box is inactive.
You said:
1. Copy this .bin to / tmp
2. Open telnet and login (via the IP address)
(...)
But I don't have an IP to connect with the Box.
So, I don't have Telnet.
It seems a hardware problem. Issue in the memory block.
Only a specialized technician can recover this Box.
Thank you very much for your help.
Hugs.
#
temp /windows?is the same with jtag
Display More#
Hello, jhon32
I didn't understand: temp / windows? Is the same with jtag
Are you saying to simulate "jtag" by placing the files in that folder?
But the connection to the Box will not be made ...
Thank you very much for your help.
Hugs.
#
i make jtag for old dm500 and all files is on pc , i work with programs ,if you whant make a ideia i atached
must be like this
:~# flash-rescue /tmp/*.bin
Warning: Could not read CA!
Warning: Please consider updating your rescue loader!
Manufacturer ID: c2
Memory type : 20
Memory density : 19
read id ok
comparing 2847 sector
on you try all cable must be disconected like hdmi
Only if your receiver dont go in recovery mode
For rescue DM900 use usb cable and putty (serial port).
Start receiver and push ctrl+C to enter in cfe mode. Use usb stick for rescue file downloaded from internet.
ifconfig eth0 -auto
show devices
dir usbdisk0
boot usbdisk0:zImage-rescue-xxxxx
and usb must format in exfat normal,not quiq !eject from bar icons
this is alot help ,is enuf help
But I don't have an IP to connect with the Box.
So, I don't have Telnet.
https://board.newnigma2.to/wbb…M920-DM7080-USB-Recovery/
#
Hello jhon32.
As suggested, if you are in the mood and time, I ask you to log in with TeamViewer on my PC.
If you accept, tell me what I should prepare:
- Folder with files (which ones?); or do you transfer?
- Box connections (mini-usb connected to the pc + hdmi connected to the tv + net network + sat cable to the tuner)?
I await your decision and the best time (I'm in Portugal).
When you are ready, I can send you by PM the TeamViewer data.
Thank you very much in advance.
#
Display More#
Hello jhon32.
As suggested, if you are in the mood and time, I ask you to log in with TeamViewer on my PC.
If you accept, tell me what I should prepare:
- Folder with files (which ones?); or do you transfer?
- Box connections (mini-usb connected to the pc + hdmi connected to the tv + net network + sat cable to the tuner)?
I await your decision and the best time (I'm in Portugal).
When you are ready, I can send you by PM the TeamViewer data.
Thank you very much in advance.
#
you dont need conect with you with teamview , when you conect your dreambox leave only ethernet cable+ mini usb ,first time format your usb to exfat(
small <1gb,copy rescue loader to usb and put on your dreambox !after start puty
Start receiver and push ctrl+C to enter in cfe mode. Use usb stick for rescue file downloaded from internet.
ifconfig eth0 -auto
show devices
dir usbdisk0
boot usbdisk0:zImage-rescue-zImage-rescue-3.14-r0-dm900-20200227
this is bootloader, this mode is moore easy,good luck
Display More#
Hello jhon32
I followed your instructions.
The result is the same: FATAL ERROR.
I notice that the PEN is not read.
I think there is nothing to do.
I appreciate all your help. You were all impeccable.
Great solidarity. Thank you all.
Hugs.
#
not all usb flash drive is works !ytry diferent and smaller ,and not quiq format
Yes corrupted flash most probably as second bootloader fails
Emo
Взаимодействие с другими людьми
#
The problem will be in the corrupted, flash memory.
The Box, must have a qualified technical intervention.
you gave up - weak in spirit, there is a way to restore using a TFTP server, earlier in the posts you were pointed to this method..But you can't hear me
http://www.domica.biz/index.ph…15938.msg166885#msg166885
"we connect the router in a bundle-which can assign an IP address via DHCP."
"Then first check if it can automatically assign an IP address to the receiver"
open a COMMAND prompt on your computer and give the command to automatically assign an IP address to the receiver
ifconfig eth0 -auto
if you do not assign IP machine do it manually
ifconfig eth0 -addr=xxx.xxx.xxx.xxx -gw=xxx.xxx.xxx.xxx
Next, you will need the TFTP server program
Then we put zImage-rescue in the folder to your TFTP server.bin
In the TFTP server we specify the assigned IP to your receiver and give the command
boot -tftp-noclose 192.168.***.***:zImage-geo -******. bin
After successful filling, zImage-rescue.bin you can flash your receiver via a web interface preferably with a dream OS image
Don’t have an account yet? Register yourself now and be a part of our community!