This.
Oscam Icam Sky DE and UK
-
- ICAM OSCam
- kashmir
- Closed
- Thread is marked as Resolved.
There are 1,135 replies in this Thread which was already clicked 434,488 times. The last Post () by abu baniaz.
-
-
Sorry I am a newbie where is the reader.conf location? On webif files? or where? Gigablue Box is my receiver.
this is a solution
put this in reader.conf
[reader]
label = LOCAL@098D
protocol = newcamd
device =
key = 0102030405060708091011121314
user =
password =
inactivitytimeout = -1
disableserverfilter = 1
connectoninit = 1
cacheex_drop_csp = 1
cacheex_block_fakecws = 1
caid = 098D
ecmwhitelist = A3,A0,A7,B7
ecmheaderwhitelist = 80709D0000011F,81709D0000011F,8070A000000122,8170A000000122,8070A400A001,8170A400A001,8070B400B00122,8170B400B00122
group = 1
lb_weight = 85
cccreshare = 1
audisabled = 1
-
guys , is not problem in oscam
its problem with suorce , now i got new line and working without breaks ,normal
if you have this problem just change source and buy new line
many have fake lines from cache not reall source , exchange between and then not work well
JUST CHANGE SOURCE and all bee fine !!!
-
of is just some one or more persoen giving voluntarily fake dcw...so exchange with good line verifie the line before ..bcp on privat is working ok .........
-
Hi Forum contributors! I have a question...
I am running a Vu + Ultimo 4K with VTi 15.02, oscam 11715 icam emu.
My question is - I had evrrything working with a stream relay bouquet installed, but after some changes (I deleted some bouquets) and some updates to channel lists I now have a total black out on all 19.2E channels - they do not show any signal / ber rates. In spite of this I can run a manual scan of 19.2E and this runs perfectly, finding 1300 or so channels. when I tune to channels on 19.2E they are black. I think it must be a config issue with icam, but I need help getting out of this situation as the whole sat is black...
-
I know it's my same problem... (Shanewarwick)I don't know why if I tune into a sky channel from normal settings I get the satellite signal, while if I use the sky channel package from icam: streamrelay, I can't get the SNR signal! erros : no data on the transponder
Thanks for your helpHi Forum contributors! I have a question...
I am running a Vu + Ultimo 4K with VTi 15.02, oscam 11715 icam emu.
My question is - I had evrrything working with a stream relay bouquet installed, but after some changes (I deleted some bouquets) and some updates to channel lists I now have a total black out on all 19.2E channels - they do not show any signal / ber rates. In spite of this I can run a manual scan of 19.2E and this runs perfectly, finding 1300 or so channels. when I tune to channels on 19.2E they are black. I think it must be a config issue with icam, but I need help getting out of this situation as the whole sat is black...
-
Just try another set of settings....
And send them to your box with dreambox edit or a similar software...
This one is working just fine!
-
Strange thing, but all day today sky de channels are working perfectly without any alteration on my end (octagon sf8008, openatv 7.2)!
-
Hello
It was working perfectly for me until a week ago.
Now along the same lines, when moving from one channel to another the oskam turns off and stops working. A reboot of the receiver is required to run. What could it be... With the newest version of oscam 11718, I also want openpli... With dm920
-
Oscam.config
[radegast]
port = 9090
allowed = 127.0.0.1,192.168.0.0-192.168.255.255
user = icam
[streamrelay]
stream_ecm_delay = 5
stream_relay_ctab = 098D
stream_relay_icam_ctab = 098D
Oscam.user
[account]
user = icam
group = 1,2,3,4,5
[account]
user = Receiver
au = 1
group = 1
oscam.dvibapi
###### tenten ######
###HD+ GERMANY###
P: 1843:000000 # HD+
P: 1830:000000 # HD+
###SKY GERMANY###
P: 098D:000000
P: 09C4:000000:119A # clipmyhorse
P: 09C4:000000:14B7 # Puls4HD
P: 09C4:000000:1198 # weidwerk
P: 09C4:000000:1196 # esport1
P: 09C4:000000:1197 # EDGEsport
P: 09C4:000000:2E87 # RTL HD Austria
P: 09C4:000000:EF8B # sixx hd Austria
P: 09C4:000000:EF8C # pro7 Maxx hd Austria
P: 09C4:EF8A
P: 09C4:000000:14B4
P: 09C4:000000:2EA5
P: 09C4:000000:14B5
P: 09C4:000000:2E91
P: 09C4:000000:14B6
P: 09C4:000000:527E
P: 09C4:000000:527D
P: 09C4:000000:152D
P: 09C4:000000:152E
P: 09C4:000000:EF14
P: 09C4:000000:2E9B
###CYFRA - NC+ - POLSAT###
P: 1884:000000:32DE # Canal Sport 1
P: 1884:000000:13EE # Canal Sport 2
P: 1884:000000:12C2 # Canal Sport 3
P: 1884:000000:12C3 # Canal Sport 4
P: 1861:000000
P: 1813:000068:37B1
P: 1813:000068:0C1F
P: 1813:000000
P: 1813:000068
P: 1803:000000 # Polsat
P: 1803:000000:3ABD
P: 1803:000000:13F3 # ELEVEN SPORT 1
P: 1803:000000:13F5 # ELEVEN SPORT 2
P: 1803:000000:13F8 # ELEVEN SPORT 3
P: 1803:000000:32CE # ELEVEN SPORT 4
P: 0B01:000000
P: 0B01:000000:08A2
P: 0B01:000000:012E
P: 0B01:000000:012F
P: 0B01:000000:0131
P: 0B01:000000:013A
P: 0B01:000000:3A99
P: 0D95:000004
P: 0100:000068
P: 0100:00006A
P: 0100:00006C
P: 0100:00006D:012D
P: 0100:000000
###AUSTRIA###
P: 0D98:000000
P: 0D98:000004:1194 # ORF
P: 0D98:000004:1013
P: 0D98:000004:101D
P: 0D98:000004:100A
P: 0D98:000004:14C1
P: 0D98:000000:14C2
P: 0D98:000004
###CSAT&FRANCE
P: 0500:000000
P: 1811:003315 # CanalSat
P: 1811:003311 # CanalSat
P: 1811:000000 # CanalSat
P: 1805:000000 # Mediaset DTT
###SPAIN###
P: 1810:000000 # Movistar +
P: 0500:040810 # SRG
P: 0500:050F00 # XXX
P: 0500:030100
P: 0500:041F00
P: 0500:030b00
P: 0B00:000000
P: 0B02:000000 # FOCUS
P: 4ABF:000000
########### IGNORE ########
I: 09C4:000000
#I: 098C:000000
Nline
[reader]
label =
protocol = newcamd
device =
key = 0102030405060708091011121314
user =
password =
inactivitytimeout = -1
disableserverfilter = 1
connectoninit = 1
caid = 098D
group = 1,2
audisabled = 1
-
Radegast and icam user is not needed anymore all oscam Icam patched like V3 have dvbapi patch!
-
Radegast and icam user is not needed anymore all oscam Icam patched like V3 have dvbapi patch!
where can i find this oscam
-
To ask
Skyde icam channels starved only with oscam icam or also with Ncam?
Can anyone where it works stable post exactly whatever confins to use. You can also send a private message
thanks
-
To ask
Skyde icam channels starved only with oscam icam or also with Ncam?
Can anyone where it works stable post exactly whatever confins to use. You can also send a private message
thanks
ThreadEverything you need for ICAM - Sky ITALIA, Sky UK & SKY DE - All Enigma2 Images and ReceiversIts now possible to view Sky Germany, Italia, and UK channels with NCam or OSCam that has an ICam patch along with a custom streamrelay channel list.
First thing you need to do is install either NCam or OSCam. Both are configured exactly the same way.
These files come with everything already pre-configured for ICAM .
No other edits are required, just add your reader to ncam.server or oscam.server. Configs are found in /etc/tuxbox/config
OSCam for All E2 Devices & Images .ipk (OSCam for Sky DE, IT … -
until last week it worked perfect now it crashes every 10 seconds and has something changed?
-
I'm having the same thing, it's been happening for a long time and I don't know why 😒
-
All works fine.Find better server with real cards and no trouble with freezing
-
Tutto funziona bene. Trova un server migliore con carte reali e nessun problema con il congelamento
I always have the same line so what's the problem?
-
it works on vu zero 4k, but it doesn't work on vu zero hd on pli 4.0 image, using the same config only get ecm without picture, because there's no response from server. Is there a fix?
-
it works on vu zero 4k, but it doesn't work on vu zero hd on pli 4.0 image, using the same config only get ecm without picture, because there's no response from server. Is there a fix?
Try to change your image to latest one.
OSCam Support Forum
Configs, discussion, downloads and guides for OSCam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!