As the title says i'm looking for a s@y italia boxes (like myskyhd or sky hd) firmware dump
Thank you
There are 31 replies in this Thread which was already clicked 2,705 times. The last Post () by djangel912.
As the title says i'm looking for a s@y italia boxes (like myskyhd or sky hd) firmware dump
Thank you
HOW TO DUMP ANY DEVICE
by ch341a DRIVE
Immagine 2022-10-11 220505.png
use hex editor to read your dump file you can setup 8 bytes or 16 bytesImmagine 2022-10-11 220958.png
Immagine 2022-10-11 221033.png
The chip could have several numbers including date codes, but the important one has 24, 25 or 93 in it. It will usually start with a letter for manufacturer (AT for Atmel, M for STM etc) but not always and may be followed by a letter or two for series. It will end in a number giving the memory size, in bits not bytes.
types of eeprom:
eeprom 95080.
cmos eeprom.
eeprom transistor.
eeprom 28 pin.
eeprom spi i2c.
eeprom clip soic 8 pin most used by stb
ch341a software
siberia prog
pin tester
most 4k used cpu
Thank you so much!
the "only" problem is that the sky decoder that i have (Pace ds831ns HD) does not have any eeprom, but the decoder uses a NAND, making it pretty hard/expensive to dump, here is a photo of the box motherboard in case some of you will find it useful
PS: i've already tried to connect via UART to the box by guessing the tx and rx contacts with no success (now i've got a box that doesn't output anything on the tv :( )
Thank you so much!
the "only" problem is that the sky decoder that i have (Pace ds831ns HD) does not have any eeprom, but the decoder uses a NAND, making it pretty hard/expensive to dump, here is a photo of the box motherboard in case some of you will find it useful
PS: i've already tried to connect via UART to the box by guessing the tx and rx contacts with no success (now i've got a box that doesn't output anything on the tv :( )
can you send me the cpu name for complete please?
Yeah, sorry i didn't notice that it was covered by thermal paste
It is a Broadcom bcm7325skfsba1g
Yeah, sorry i didn't notice that it was covered by thermal paste
It is a Broadcom bcm7325skfsba1g
Yeah, sorry i didn't notice that it was covered by thermal paste
It is a Broadcom bcm7325skfsba1g
can you tell me also what type of nand use that stb ? I mean the name of nand
is somtething like this TC58NVG1S3.... and ??
I think is TC58NVG1S3EBAI5
Yeah, sorry i didn't notice that it was covered by thermal paste
It is a Broadcom bcm7325skfsba1g
if your nand is TC58NVG1S3EBAI5 (let me know) you need to fix voltage in ch341a from 5V to 3.3V
fix from 5v to 3.3v ch341a
i think that this box uses 2 nands (?)
because one nand has written NAND on it and it is from st
the other one is from spansion and it had a label attached to it with writed NDS (the card that this box uses) and a number (1.38 if im not wrong)
idk, here attached a close-up photo of the 2 chips
BTW I've already got a modified ch341a that i've used to mod a pc bios
i think that this box uses 2 nands (?)
because one nand has written NAND on it and it is from st
the other one is from spansion and it had a label attached to it with writed NDS (the card that this box uses) and a number (1.38 if im not wrong)
idk, here attached a close-up photo of the 2 chips
datasheet
NAND02GW3B2DZA6
-------------------------------------------------------------------------------------------------------------------------------------
gl032n90ffis3
Thank you so much!
Now, how should i connect this nand to a ch341a?
I could de-solder it, but it is bga, so pretty hard to solder wires to it
Thank you again!
Thank you so much!
Now, how should i connect this nand to a ch341a?
I could de-solder it, but it is bga, so pretty hard to solder wires to it
Thank you again!
do you have 8 pins right for both nand? the welding seems smd so you have to do it manually, be careful
I found out this datasheet that includes the fbga connections
Don’t have an account yet? Register yourself now and be a part of our community!