sorry missed tour question, I have the cable in Port A
Add Thor 0.8 w Satellite Gigablue UHD UE 4K
- Skalman
- Closed
- Thread is marked as Resolved.
There are 41 replies in this Thread which was already clicked 1,698 times. The last Post () by abu baniaz.
-
-
-
Back
-
.If your cable is only in port A and you don't have any more cables connected to ports B, C, D. Try only thor, and don't have these other satellites to search for, then see what happens. That c band thor 5/6/7 is thrown out and try another thor if you have one.
-
You should try satellite if you have 0.8W Thor 5/6/7 Intelsat 10-02. I see you have c band thor 5/6/7 Intelsat 10-02 and ku-band Thor 5/6/7 Intelsat 10-02.
-
I had a read back and if you look at his first pic in post 15 he has input frequency for ALLENTE and got a signal and a lock, all he had to do then was press green to scan.
https://www.linuxsat-support.com/cms/attachment/237409-img-5401-jpg/
we have a communication problem me thinks
-
I don't know if we understand each other well. I see that your cable is plugged into receiver A. I was thinking of the disagc a/b/c/d which is at the satellite antenna, or does that cable go directly from the LNB head
-
PI did you click on my link!!!
-
He says that he can't find anything on the thor 0.8 w satellite
-
IMG_3904.jpgThis is what he said in his first post " I have a CI card and a subscription with Allente. """ !! That frequency in my link is ALLENTE!!! of his search is the channel.!!!
-
I hope he will solve the problem he has.
-
Change in Setup Tuner A , because you have only one LNB. Disecq is only if you use more LNB's. For scan use automatic scan ( all "yes" )
Configuration mode > simple
Mode > single ( see my screenshots once again )
-
Wrong
Mode = Diseqc a/b/c/d
Correct
Mode: Simple
Use remote to and press right/left to change it to simple.
You are wasting your time going into signal finder, scanning etc. Set your tuner correctly first. Once you tuner is set correctly, the rest of the system should not let you select satellites that you have not set/cannot receive.
-
I don’t have any Diseq switch, the cable goes directly from LNB to the receiver.
-
These are the channels I have subscription to
https://www.tvchannellists.com…annels_on_Allente_(Sweden)
https://www.satellite-calculations.com/DVB/1westall.php?//Telenor////
-
Forget scanning for now, set the tuner correctly first. We can do the scanning later.
-
I found this
-
Abu, he is not even reading the posts, in post 15 he put in the frequency for ALLENTE and got a signal and a lock, all he had to do then waa press the green button to scan. I then posted a clip from lyngsat to show that e was receiving 0.8w. He has now posted the channels he has subscribed to!!
This is the most weird thread I have ever seen.
https://www.linuxsat-support.com/cms/attachment/237409-img-5401-jpg/
-
sk you have a prblem in that you are totally lost and messing. your tuner is set up wrong you only have one dish and one cable so make tuner like this
simple, single, then put in sat 0.8w, then its no no, the green to save that sat, then go to manual scan seelct type of scan single then select 08w, yes no no the green to scan and wait.
NB you dont have a motor or do you??
-
Configuration mode is good > Simple. Change Mode , left / right with remote to > Single , not Positioner or Disecq.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!