Display MoreIt is also possible that this is not a software error but a hardware error (faulty flash memory).
Therefore, the first step should be to diagnose the problem.capture_013_18012026_213238.png
or
do you know how to read with the PUTTY
UNO 4K SE Flash
- skorpionxx
- Thread is marked as Resolved.
There are 65 replies in this Thread which was already clicked 5,811 times. The last Post () by skorpionxx.
-
-
did you try with file from qvadis54 ? Unzip directly to usb stick and try to flash.If that does not work then box is for repair or your bin.
Did you try other power unit ?
How
-
power unit : take other from 12 volt 3.5 amps.
file : download rar and unzip to stick and flash normal. #39
Ps : have patience when rebooting
-
power unit : take other from 12 volt 3.5 amps.
file : download rar and unzip to stick and flash normal. #39
Ps : have patience when rebooting
the Damies bring it back I will never install multibboot again
-
before you do something in flash google is your best friend and you could see that it only works with a usb stick for small memory
-
before you do something in flash google is your best friend and you could see that it only works with a usb stick for small memory
i'm not doing anything with the serial cable just checking how to get the boxing data from the PUTTY
-
from new york to LA jumping all over. Just follow and give FB on wath you realy do .All over for me till another time
-
do you know how to read with the PUTTY
Push Open and Switch ON box
-
Have you installed the driver for the virtual COM port, or do you have a PC with a direct COM port as shown in the image above?
-
Have you installed the driver for the virtual COM port, or do you have a PC with a direct COM port as shown in the image above?
apple laptomp with a wirtual machine windows installed
the Driver is installed but I don't know how to start a road trip is to be attached to the net with a cobble
sorry, I didn't have time to get back to you earlier
Screenshot 2026-01-21 at 23.56.28.png
Screenshot 2026-01-22 at 00.07.18.png
you see on the serial port 3 when I start and turn on box starts reading it and stops and see, there's no letter only that
-
I'm packing it up to HM-Sat tomorrow
Yes best thing to do and hopefully not cost to much :)
-
Yes, VU+ turners are compatible with these
Supported VU+ set-top boxes:
VU+ Uno 4K
VU+ Uno 4K SE
VU+ Duo 4K
VU+ Duo 4K SE
VU+ Ultimo 4K
-
Display More
Yes, VU+ turners are compatible with these
Supported VU+ set-top boxes:
VU+ Uno 4K
VU+ Uno 4K SE
VU+ Duo 4K
VU+ Duo 4K SE
VU+ Ultimo 4K
Have you installed the driver for the virtual COM port, or do you have a PC with a direct COM port as shown in the image above?
hello, I'm a resiver in the service
-
you see on the serial port 3 when I start and turn on box starts reading it and stops and see, there's no letter only that
The port speed is usually set to 115200, but according to the picture, it looks like the cable is connected incorrectly because the boot sequence is not displayed correctly, which be seen in the video.
-
you see on the serial port 3 when I start and turn on box starts reading it and stops and see, there's no letter only that
The port speed is usually set to 115200, but according to the picture, it looks like the cable is connected incorrectly because the boot sequence is not displayed correctly, which be seen in the video.
what do you think could be a big malfunction or not
-
what do you think could be a big malfunction or not
Until you check the cable functionality, you don't know where you stand.
VU+ UNO 4K SE PVR ready Linux Enigma2 Receiver UHD 2160p
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
