Help required with debian, smargo setup.

Hi, all i did have a post on the end of "Automated Oscam/CCcam 2.1.3 Install Package For Debian 6" but it disappeared, so here i go again...

I have linux setup, with smargo reader

cccam & oscam are running fine and i can access the web interfaces...

im having issues with my smargo.

oscam logs, read>
25/09/2012 16:30:30 8766A28 r Found smartreader device 002:005
25/09/2012 16:30:30 8766A28 r ***uk [smartreader] Reader initialized (device=002:005, detect=cd, mhz=357, cardmhz=357)
25/09/2012 16:30:31 8766A28 r ***uk [smartreader] card detected
25/09/2012 16:30:35 8766A28 r ***uk [smartreader] usb bulk write failed : ret = -4
25/09/2012 16:30:35 0 ***uk [smartreader] SR: USB bulk read failed with error 5
25/09/2012 16:30:35 8766A28 r ***uk [smartreader] usb bulk write failed : ret = -1
25/09/2012 16:30:35 0 ***uk [smartreader] SR: USB bulk read failed with error 5
25/09/2012 16:30:35 8766A28 r ***uk [smartreader] usb bulk write failed : ret = -1
25/09/2012 16:31:31 8766A28 r ***uk [smartreader] Error activating card.
25/09/2012 16:31:31 8766A28 r ***uk [smartreader] card initializing error

lsusb read>
root@cmysserverr:~# lsusb
Bus 002 Device 005: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC

dmesg read>
[ 0.000000] console [ tty0] enabled
[ 1.176887] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.177137] 00 : 06 : ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 5.058880] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 5.058974] usb 6-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 6.683229] usb 6-2: usbfs: interface 0 claimed by ftdi_sio while 'brltty' sets config #1
[ 6.705254] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 4.765154] USB Serial support registered for generic
[ 4.765223] usbcore: registered new interface driver usbserial_generic
[ 4.765225] usbserial: USB Serial Driver core
[ 5.057088] USB Serial support registered for FTDI USB Serial Device
[ 5.057146] ftdi_sio 6-2:1.0: FTDI USB Serial Device converter detected
[ 5.057188] usb 6-2: Detected FT232BM
[ 5.057190] usb 6-2: Number of endpoints 2
[ 5.057192] usb 6-2: Endpoint 1 MaxPacketSize 64
[ 5.057193] usb 6-2: Endpoint 2 MaxPacketSize 64
[ 5.057195] usb 6-2: Setting MaxPacketSize 64
[ 5.058880] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 5.058974] usb 6-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 5.058993] usbcore: registered new interface driver ftdi_sio
[ 5.058995] ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
[ 6.683229] usb 6-2: usbfs: interface 0 claimed by ftdi_sio while 'brltty' sets config #1
[ 6.705254] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0

Any suggestions please?
is my smargo card faulty?

after lots more researching it seems i have a conflict :
usbfs: interface 0 claimed by ftdi_sio while 'brltty' sets config #1
i removed this, by apt-get remove brltty. rebooted and now i get CARDOK[9 Entitlements] on oscam..

but cccam still not seeing the card, even thought i added :
SERIAL READER : /dev/ttyUSB0 smartreader+ to SERIAL READER : /dev/ttyUSB9 smartreader+ in the CCcam.cfg file.

not sure if this was the right thing todo, if anyone else had experienced this, please let me know.

Hello and thanks for reply.
I think oscam is correct, as i dont have any errors.. it lists tier info, with expiry dates..
Same with entitlements, i will show tier info with start/end dates.. the information is meaningless to me at the mo, and couldnt find a screen shot of what it should look like, but im guessing its all ok

I removed the SERIAL READER lines from the CCcam.cfg file now. is there an example of what the CCcam file should look like with my setup.. to be honest i done a lot of trial and errors trying to get past the card reader problems i was having.

CCCam is the same as yours,

my oscam files are:

.server
[reader]
label = ***UK
protocol = smartreader
device = 005:002
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
emmcache = 1,3,2
group = 1
caid = 0963




.user
[account]
user = linuxsat
pwd = support
monlevel = 0
uniq = 0
group = 1
au = ***UK
caid = 0963




.conf
[global]
nice = -1
logfile = /var/log/oscam.log
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1




[webif]
httpport = 8888
httpuser = 
httppwd = 
httprefresh = 5
httphideidleclients = 0
httpallowed = 192.168.0.0 - 255.255.255.255
debug = 255




[newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000
keepalive = 1

should i see an active card still on the CCcam web interface?
as im still getting just :
Server connections: 1

+----------------------+------------+-------+--------+----------------+-------+-------------------------------+
| Host | Connected | Type | Version| NodeID | Cards | CAID/Idents |
+----------------------+------------+-------+--------+----------------+-------+-------------------------------+
|127.0.0.1:34001 | |newcamd| | | 0 | |
+----------------------+------------+-------+--------+----------------+-------+-------------------------------+

Arh misses that port settings...
Changed it, and now its connected !!

Now i just need to add my friends and families account.
Can u point me to the correct guide for my setup.. or give me examples.

Thanks Master G

Thanks Master G, all up and running, didnt realise that bit was so simple.

Gunna restart from the beginning now, the bit which screwed me the most was the error conflict : [ 6.683229] usb 6-2: usbfs: interface 0 claimed by ftdi_sio while 'brltty' sets config #1

maybe Ten Below can mention this in his guide.

Appreciate your time :mrg: