protest to weakly support of Vu plus Company.

Quote from digidude

the outputs of the power supply will be fine, untill they are put under load. its possible to send the image via putty, but, this will be a SLOWWWWW process, and does have the capability to completley damage your receiver beyond all form of software recovery.

disconnect EVERYTHING, including the internal HDD, TV, dishes, rear USB, everything, so that all that is connected is the power lead, ethernet lead, and serial lead

or, with everything else disconnected, try a microSD card in a mini USB adaptor for USB flashing, try flashing only a bootloader first

I had done it. Only motherboard is on power supply. No HDD no lnb no usb but not read any usb.

Quote from mrgmx

introduction??????????????

ok. Done. Please

Please help me. Why there is not anyone know how i should solve my Problem in this box.
Please.

This is my Putty log. Are you think the box need to be Jtag ??

BCM73350010
012

Shmoo Version=1.9

MEMC-00000000 RW=00000010 WW=0000004D G=00000001 R=00000008 W=00000014
MEMC-00000001
RW=00000010 WW=00000051 G=00000001 R=00000009 W=00000006 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Thu Sep 29 12:01:32 2011 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd

DDR Freq: 395MHz
CPU speed: 405MHz
Memory Config: 32+16 non-UMA
Device Tech: 1Gb
Total memory: 384MB
Boot Device: NAND
ECC: Hamming
Total flash: 128MB

Initializing USB.
**Exception 32: EPC=8701D8E8, Cause=0000801C, VAddr=00000000
RA=8701DB28, PRID=0002A044

0 ($00) = 00000000 AT ($01) = B0480000
v0 ($02) = 00000000 v1 ($03) = 87020000
a0 ($04) = B0480400 a1 ($05) = 87040000
a2 ($06) = B0480390 a3 ($07) = 00000000
t0 ($08) = 00000043 t1 ($09) = 00000055
t2 ($10) = 00000046 t3 ($11) = 87069570
t4 ($12) = 00000001 t5 ($13) = 870470E8
t6 ($14) = 00000000 t7 ($15) = 07600000
s0 ($16) = 8701D8CC s1 ($17) = B0480400
s2 ($18) = 8700A4B8 s3 ($19) = 38C00000
s4 ($20) = 00008000 s5 ($21) = 00000040
s6 ($22) = 00010000 s7 ($23) = 00000040
t8 ($24) = 00000000 t9 ($25) = 870471F4
k0 ($26) = 00000000 k1 ($27) = 00000000
gp ($28) = 8704E210 sp ($29) = 87148768
fp ($30) = BFC00AA0 ra ($31) = 8701DB28

*** Waiting for system reset ***

Quote from thatfellow

Just noticed this from alian

Do you even need an IP address for a serial flash, Its usually just a com port..

If so, try set a static IP address within your router, this will reserve that IP address & hopefully hold it during the flash.

linuxsat-support.com/cms/attachment/11993/
linuxsat-support.com/cms/attachment/11994/

good luck

Display More

Thanks a lot.
After connecting serial cable and network cable from pc to Vu Duo box & set my pc network IP : (not difference between Static IP & DHCP)
I use VuUtil to connecting to the box, but after turning the box on it goes to 40% stopped & did not Set IP. Why ?

Quote from alian

Thanks a lot.
After connecting serial cable and network cable from pc to Vu Duo box & set my pc network IP : (not difference between Static IP & DHCP)
I use VuUtil to connecting to the box, but after turning the box on it goes to 40% stopped & did not Set IP. Why ?

Vu Util not works anyway. Is there another program for serial flashing Vu duo ???