Hi guys i have a new Alsat Dark Superior DiSEqC All Metal Geared Motor 'the problem is it seems slower than my older
Technomate TM-2600 Super .
i used to have usauls set up with my
Technomate TM-2600 Super and it was fine but when i set up usuals on my Alsat Dark Superior DiSEqC All Metal Geared Motor it seems to work ok for a bit then get lost and stops working should it be set to 1.2 disqc
not sure if i've made the wrong choice
its hard to say if you made the wrong choice only you will answer that !
Other views could be ?
so its slower than your old motor ? YES -
Make sure you are attempting to tune to a Horizontally polarized signal _ This will feed the motor with 18v and make the movement quicker.
Aboout the diseq memory i dont know !
if you didn't change anything in the settings i cant see why there would be a problem ! should be on usuals setting for auto locate option or 1.2 if you want to manually store the positions !
I'm not 100% sure but I think it should be on diseqc 1.2.
you have made the choice of buying a different motor to the one you knew worked well/faster,etc.
Therefore there is no problem.
Made the wrong choice ??
As already answered, ONLY YOU can decide that!!
case closed.
Hello buddy,
Just out of interest what size of dish have you got attached to this motor???
I had one of these with a triax 110 mounted on it, gave me problems no end, I went back to the TM 2600 in the end and have never had a problem since.
Plus side was though I was able to offload the Alsat motor to a guy in spain!!! :snicker:
QuotePlus side was though I was able to offload the Alsat motor to a guy in spain!!!
which is working perfectly after downgrading from the 110 to a 90 dish!!!! :thumbsup:
i have one of these motors with a 1m dish on it and it runs well even with all the bad weather to.
im using the ALSAT DARK SUPREME LED ALL METAL GEAR MOTOR and works well...
im using the motor on a OP125 Gibertini 1.25 M dish.
this is the one of the fastest motor ive used..
im using the ALSAT DARK SUPREME LED ALL METAL GEAR MOTOR and works well...
im using the motor on a OP125 Gibertini 1.25 M dish.
this is the one of the fastest motor ive used..
Think i may have an underlieing problem somewhere i will start another thread i think with all the details on
im using the ALSAT DARK SUPREME LED ALL METAL GEAR MOTOR and works well...
im using the motor on a OP125 Gibertini 1.25 M dish.
this is the one of the fastest motor ive used..
can i ask you are you using usuals
Quotecan i ask you are you using usuals
yes i do mate
OK so if i have B tuner connected to a static *** dish and A tuner connected to the motor/dish what should my setting be in the image ?
becuase for some reason the duo kind of lost where it was and when i went outside to move it manualy it didnt budge no power ?
my settings is A tuner for motor set like i said in the other post and B tuner is on a sly dish set to simple,single,28e,send diseqc no and works a treat to.
my settings is A tuner for motor set like i said in the other post and B tuner is on a sly dish set to simple,single,28e,send diseqc no and works a treat to.
thanks mate thats very helpfull what image you running ?
im on vix but the tuner configs are the same realy in most images
I have just changed my motor to a darksat motor and I to had problems with using usuals, It would find the sat then move past it, not on all the sat and but just every now and again. I changed to 1.2 and now everything is all good
thanks mate how did you set up 1.2
I used Usuals to find the sat but then changed it in setting and saved it so it now uses 1.2
Don’t have an account yet? Register yourself now and be a part of our community!
