hi
my vu+duo not start
i tired to upgrade bootloader and image
my receiver upgrade with all image but not started
i see in tv this message : starting GUI and not starting
and in front panel this message : vu+duo
please helpme
vu+duo not start
- tps_star
- Thread is marked as Resolved.
-
-
Hello buddy, can you tell us if this duo is a original or clone please, what image was on the duo before you tried to upgrade it?
-
thancks for reply
vu+duo is orginal
i try this image :
BH 1.7.4 Vu Duo Full Backup 07052012
BlackHole-2.0.2-bm750
BlackHole-1.7.5-bm750
and this boot loader :
duo_cfe_3_0_usb
regard -
Ok you need to update the bootloader first, is this updating correctly? The display on the front will tell you to remove the usb and reboot the same as after a image update if it has worked correctly.
Is there and devices connected to the rear usb ports when trying to update the image? Have you another usb stick you can use to try to flash the new image on?
-
i update first bootloader and second image
when update is finish i see in front panel this message remove the usb and reboot
i try to update with front and rear usb but not working
you have any idea?
you have flash dump file this receiver for program with universal programmer ? -
i try to update with front and rear usb but not working
you have flash dump file this receiver for program with universal programmer ?
Only use the front usb port to flash a image on, I have no idea what you mean by flash dump file.
Have you tried to flash on the original Vu image , see if that works.
-
same as i posted in your solo post mate but obv use the duo backup on this 1
-
please help me
-
please help my problem not solved
with this problem i not have picture from av or scart socket just hdmi giveme picture
and cpu my receiver is very hot is normal or cpu is damaged ? -
the cpu tends to hot to very hot thats normal with a vu duo/solo2
if it stays cold your fcked
try buttin back the image you had in it or an original vix image LOL -
the cpu tends to hot to very hot thats normal with a vu duo/solo2
if it stays cold your fcked
try buttin back the image you had in it or an original vix image LOL
i change nandflash my receiver with working receiver but my receiver not working
is possible giveme link original vix image
and how i can know my vu+duo is orginal or clone?
is possible upgrade my receiver with clone image ?
if ok please giveme clone image link
please hepme -
only today for the 1st time a friend brought me his solo as the image had
screwed up, so i turn it no picture for 10mins then all ok
re-flashed it no picture for a few mins the in b&w then colour
then ok.. if you leave it on it runs ok..thermally intermittent normally
its the other way round, when hot/warm Hmm unusual LOL
ps. i always but a fan on these cpu's as they tend to get very hot!! -
i need number this cap and resistor in bottom side mainboard
1: C532
2: C348
3: C507
4: R501
PLEASE HELP MEmy problem not solved
please helpmeplease helpme
i upgrade this receiver with many image but my problem not solved i change flash this receiver with working receiver but not work
i think my receiver have hardware problem not software problem
very good upgrade
but not picture video from av output and just hdmi have picture and hang in starting GUI -
What actually Happens when you start box?
Does image load up and then hang? Revolving spinner in top corner or anything like that?
do you have a rs232 cable? A seperate small connecting board? Any stickers saying use hardware from this source only or V2 or V3 stickers on?
what images have you tried just the newer? Or older ones also?
-
i used old and new image but not working
mainboard pcb is ver2.3
i have rs232 cable
and Revolving spinner in top corner picture tv -
Any stickers on outside of box? You have the cable how about the small motherboard with 9 pin connectors either end?
I think you may have a clone? where did you get from? how much did you pay?
-
not clone and orginal
tomorow i uploade picture from mainboard and tv picture -
the cpu tends to hot to very hot thats normal with a vu duo/solo2
if it stays cold your fcked
try buttin back the image you had in it or an original vix image LOLi'm not quite sure what your basing that on but i have a stack of 5 receivers in font of me now with a DUO LE at the bottom and a solo2 at the top and the solo2 is warm to the touch and always is.
-
-
Do the flash update as you did before (From Front USB) but when prompted to "remove the usb and reboot" power off the box from the back button, but leave it off for 5 minutes before powering it back on..
I have heard that this is some safety built in to stop the processor getting damaged. I had a very similar problem with an older model Duo and this method worked perfect for me..I cant link to the official ViX downloads but you can just google:
openvix-builds
VU+ DUO PVR Ready Linux Enigma2 Receiver Full HD 1080p
Download VUPlus Images and Enigma2 Team Support from Black Hole, OpenATV, OpenBH, Open Black Hole, OpenDroid, OpenESi, OpenHDF, OpenLD, OpenPLi, OpenSPA, OpenViX, Open Vision, PKT Hyperion, PurE2, SatDreamGR, VTi.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!