amiko alien2 E2 cccam

hello, how do I insert a line cccam in E2 Amiko Alien 2?
I installed oscam ymodv-t39, Rsp Satbox4all Image-E2-GM-7162-triplex mod.Arthur
where I insert the line cccam?thx

good morning, after saving the file oscam.server send it to the receiver via FTP? thx

Quote from rami

#[reader]
#label = newcamd_server
#protocol = newcamd
#key = 0102030405060708091011121314
#device = host and the port
#account = user, passwd
#group = 2
##########################################################
# #
# All lines preceded by "#" are comment lines so #
# use this model for all your readers ( up to 32 ). #
# A C: line is a CCcam reader , a N: line is NewCamd #
# reader , the internal card readers are also shown. #
# A card reader must always to specify the CAID. #
# #
##########################################################
#
# this is an example of how to connect a CCcam server
# this line acts as a cccam 2.0.11 client (recomended)
#
#[reader]
#label = dreambox1
#enable = 1
#protocol = cccam
#device = your host and port
#user = user
#password = passwd
#cccversion = 2.2.1
#cccmaxhops = 3
#group = 1
#inactivitytimeout = 1
#reconnecttimeout = 30

#
#[reader]
#label = internal_hrt
#enable = 1
#protocol = internal
#device = /dev/sci0
#services =
#caid = 0500
#detect = cd
#mhz = 500
#cardmhz = 500
#ident = 0500:020A00
#group = 2
#emmcache = 1,3,2
#ecmcache = 1
#lb_weight = 100
#
#[reader]
#Enable = 1
#Label = orf-camd3
#Protocol = camd35
#Device = 127.0.0.1,30001
#Account = test,pass
#CAID = 0D05
#Group = 1
#
# this is an example how to connect to a NewCamd server
#
# this is an example how to "read" a na*ra card internal(e.g. HD+/HD01)
#
# [reader]
# Label = HD plus
# Protocol = internal
# Device = /dev/sci0
# detect = CD
# EMMCache = 1,1,2
# group = 3
# CAID = 1830
# rsakey = BF358B5461863130686FC933FB541FFCED682F3680F09DBC1A23829FB3B2F766B9DD1BF3B3ECC9AD6661B753DCC3A9624156F9EB64E8168EF09E4D9C5CCA4DD5
# boxkey = A7642F57BC96D37C
#
# this is an example how to "read" a na*ra card internal(e.g. HD+/HD02)
#########use following entry in oscam.services(required)#######
####[hdplus]
####caid=1843
####srvid = EF10,EF11,EF14,EF15,EF74,EF75,EF76,EF77,5273,5274
#########
#
# [reader]
# Label = HD plus
# Protocol = internal
# device = /dev/sci0
# detect = CD
# EMMCache = 1,3,2
# group = 4
# CAID = 1843
# ident = 1843:003411,000000,008011 #not required#
# rsakey = BF358B5461863130686FC933FB541FFCED682F3680F09DBC1A23829FB3B2F766B9DD1BF3B3ECC9AD6661B753DCC3A9624156F9EB64E8168EF09E4D9C5CCA4DD5
# boxkey = A7642F57BC96D37C
# cardmhz = 368
# mhz = 368
#
# this is an example how to "read" a nagra card internal(***)
#
# [reader]
# Label = ***-Test
# Protocol = internal
# Device = /dev/sci0
# detect = CD
# mhz = 600
# cardmhz = 600
# EMMCache = 1,1,2
# group = 5
# CAID = 1702
#
# this is an example how to "read" a Viaccess card internal(SRG)
#
# [reader]
# Label = SRG
# Protocol = internal
# device = /dev/sci0
# detect = CD
# EMMCache = 1,3,2
# services = SRG
# group = 6
# CAID = 0500
# mhz = 368
#
# this is an example how to "read" a Funcard with ORF + AS-file internal
# [reader]
# Label = ORF
# Protocol = internal
# device = /dev/sci0
# detect = CD
# EMMCache = 1,3,2
# group = 7
# CAID = 0D05
#
# this is an example how to "read" a BDC internal(C+NL)
#
# [reader]
# label = C+NL
# enable = 1
# protocol = internal
# device = /dev/sci0
# caid = 0622
# force_i***** = 1
# detect = cd
# mhz = 600
# cardmhz = 600
# group = 8
# emmcache = 1,3,2
# lb_weight = 100
# boxkey = 0000000000000000
#
#######################################################################
## smargo support ##
# External reader (smargo) requires oscam LIBUSB #
# get reader serial of smargo by telnet cat /proc/bus/usb/devices #
# smargo firmware 1.04 or higher required for getting serial #
# #
#######################################################################
#
# this is an example how to "read" ICE in smargo(IR2 caid 0648)##input reader serial###
#
# [reader]
# Label = ICE
# protocol = smartreader
# device = Serial:Reader XXXXX
# detect = CD
# EMMCache = 1,3,2
# group = 9
# force_i***** = 1
# deprecated = 1
# CAID = 0648
# rsakey = DF57B08C0F13E67BD17AD37EAAF4EAA25393F8A0EFE8ACE6708AAF97C985CBA8A6C13826963BD3092EB9FC72F773A430724706AA5E1D14E1747842D32069A12D
# boxkey = 1122334455667788
# boxid = 12345678
# cardmhz = 600
# mhz = 600
#
# this is an example how to "read" ICE in smargo(CW caid 0D95)##input reader serial###
#
# [reader]
# Label = ICE
# protocol = smartreader
# device = Serial:Reader XXXXX
# detect = CD
# EMMCache = 1,3,2
# group = 10
# CAID = 0D95
# mhz = 257
# cardmhz = 257
#
# this is an example how to "read" a na*ra card in smargo(e.g. HD+/HD01)##input reader serial###
#
# [reader]
# Label = HD plus
# protocol = smartreader
# device = Serial:Reader XXXXX
# detect = CD
# EMMCache = 1,3,2
# group = 11
# CAID = 1830
# rsakey = BF358B5461863130686FC933FB541FFCED682F3680F09DBC1A23829FB3B2F766B9DD1BF3B3ECC9AD6661B753DCC3A9624156F9EB64E8168EF09E4D9C5CCA4DD5
# boxkey = A7642F57BC96D37C
#
# this is an example how to "read" a nds card in smargo(*** V13)##input reader serial at XXXXX###
#
# [reader]
# label = ***_v13
# protocol = smartreader
# device = Serial:Reader XXXXX
# caid = 09C4
# boxid = 12345678
# detect = cd
# mhz = 368
# cardmhz = 368
# ident = 09C4:000000
# group = 12
# emmcache = 1,3,2
# blockemm-g = 1

[global]
nice = -1
logfile = /dev/null
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1

[monitor]
port = 0
nocrypt =
aulow = 30
hideclient_to = 15
monlevel = 2
appendchaninfo = 0

[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = amiko
pmt_mode = 0
request_mode = 0
#priority = 0100:000068,1803,0D03:000008,0D05,1702,0500:042700,0500:042200,0500:041700,0500:040810,1810,1830,1880,09CD,0500:32830
#ignore = 09C7,09C4

[webif]
httpport = 81
httpuser = user
httppwd = pass
httpcss = /var/tuxbox/config/blue.css
httprefresh = 15
httpallowed = 192.168.0.0-192.168.255.255
httphideidleclients = 0
httpreadonly = 0
httpsavefullcfg = 0

[account]
user = amiko
group = 1,2
au = 1
betatunnel = 1833.FFFF:1702,1834.FFFF:1722

hi copy and pas oscam gfg oscam server oscam user

just put you c line there

#[reader]
#label = dreambox1
#enable = 1
#protocol = cccam
#device = global.dyndns.org,13000 # exemple
#user = user #the user
#password = passwd# pass
#cccversion = 2.2.1
#cccmaxhops = 3
#group = 1
#inactivitytimeout = 1
#reconnecttimeout = 30

do not change nothing more

#

Display More

hello, thank you, but I do not understand what are all these lines, I want to know how do I put my line in the receiver cccam transformed ...

Quote from rami

Ok do you have enigma 2 image ans oscam

yes,oscam ymodv-t39----- Rsp Satbox4all-E2-Image GM-triplex 7162-mod.Arthur
with dccE2 oscam.server I sent the file to the receiver, but when I connect to 192 ..., I can not get the connection is continuous charging of the page,login failed,pwd ack not received

Quote from fulgas

Hi Mate,

I hope you have this sorted out. If not once you have the plugin installed, download an FTP application like filezilla,

Log in into it with:

1 - Box IP address # To find it
press Menu,
then System,
then Net setting,
then IP config# where you can read the IP if the box is connected to the Internet

2 - iN FTP app, enter, IP, root, and root-passwd.

Once you are logged in, clip on

Var /keys/ # add your cline in there as usual C: xxxx.dyndns.xxx port user passwd

3 - Go into tutbox/config/oscam.server/ # and edit the context to suit your Cline and save and reeboot the box

That's you done

Cheers

Display More

hello, I do everything as you described, but when I go over the canal and always scrambled,I tried more than one line, but all with the same result,something is still missing, but I do not know,night

Quote from englishinsiam

Try going to softcam Centre and restarting the oscam emu.

It's not complicated you put your cline info in the server file ftp it to the keys folder sometimes in var/keys sometimes in usr/keys depending on the image your using. Then restart the oscam emu from the decoder.

Sent from my GT-I9505 using Tapatalk 2

hello! picture that you're using? can you tell me your settings?
I now HRnigma2 but I can not have light.
can you help me?thx

rami,has solved all my problems,thanks very much:20_003:
support true