Home Share and Ports

Hi
Could anyone tell me if you want to share a card throughout a home network using a server STB and a number of peers whether you need to open any specific ports in your router? I'm using Oscam with Cccam on an Amiko Alien 2 running Spark with plugins.
F lines in Cccam.cfg.
Basically can you use any port and if so would that port normally need to be opened on the router? Mine's a Thomson router from Plusnet.
Thanks
Flump

Great...thanks....
So what port do you enter in the Cline?
F lines are just:
F: user pass
F: user2 pass2
right?
Cheers again!

Thanks Guys!
I've copied and pasted the settings below. Should they work ok with the F lines?
Do I have to insert "SERVER LISTEN PORT : 12000" anywhere below?
Sorry for lack of knowledge!
Flump

Oscam.conf

Code:
[global]
nice = -1
WaitForCards = 1
logfile = stdout
preferlocalcards = 1
saveinithistory = 1

[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
# protocols

[newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000;10001@0963:000000oscam.server

Code:
[reader]
label = lower card
enable = 1
protocol = internal
device = /dev/sci0
caid = 0963:000000
# 0963 is *** UK.
boxid = ********
# Oscam can read a *** card i.d, but you can also put this
# in manually
detect = cd
cardmhz = 357
# this helps the card run more smootly
group = 1
# Oscam has the concept of groups. Only users in group 1 can
# use this reader. I'm only using one group.
emmcache = 1,3,2
ecmcache = 1
blockemm-unknown = 1
blockemm-g = 1
# these ensure smooth decrypting
lb_weight = 101
# for load balancing - can be commented out.oscam.user

Code:
[account]
user = Jaxo
description = for local mgcamd or DVBAPI
pwd = CCcamExchange
disabled = 0
uniq = 1
group = 1
au = lower card
caid = 0963:000000

Thanks....
No - my server box (Amiko Alien 2 with Sly card) is running Oscam and the third party boxes are Technomate and Eaglebox (Cccam or Newcamd capability) with appropriate firmware installed. (I've had them working before on premium share.)

I only need to connect the third party boxes to the Amiko on the home network.
Cheers!

You are a star!

I will go home and try it in a couple of hours and update the thread.
Thanks again.

Flump

Right
I've managed to get all of my peer boxes to connect to my Amiko Alien2.
However none of the channels clear...... But they still do on the Amiko.
Also I have to keep turning off cccam, turning off oscam, turning on cccam and then turning on oscam after a reboot.
Getting closer !!!???
Flump

Quote from Ten Below

No problem you just need to enable CCcam protocol for cline or use newcamd to create nline in the Amiko, try this

Oscam.conf

Code:

Code

[global]
nice = -1
WaitForCards = 1
logfile = stdout
preferlocalcards = 1
saveinithistory = 1




[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255







[COLOR=#ff0000][newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000[/COLOR]




[COLOR=#008000][cccam]
port                          = 12000
reshare                       = 1
version                       = 2.1.3
nodeid                        = [/COLOR]

Display More

oscam.server

Code

[reader]
label = lower card
enable = 1
protocol = internal
device = /dev/sci0
caid = 0963:000000
detect = cd
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-g = 1
lb_weight = 101

Display More

oscam.user

Code

[account]
user                          = jaxo
pwd                           = isaknob
group                         = 1
caid                          = 0963
ident                         = 0963:000000
keepalive                     = 1
au                            = lower card

For Cline in client:

C: ipofAmiko 12000 jaxo isaknob

For nline

N: ipofAmiko 10000 jaxo isaknob 01 02 03 04 05 06 07 08 09 10 11 12 13 14

e.g 192.168.1.10

You can remove the unused protocol from oscam.conf in red or green above and of course change the username & passwords to your own if you wish.:laugh:

Display More