how to configure oscam to use as mgcamd client

There are 11 replies in this Thread which was already clicked 29,595 times. The last Post () by rooney81.

    Hi Guys.


    Im sorry if this has been asked 100s of times but I cant seem to find the answer. I have a vu solo2 running the latest vix but mgcamd seems to be acting up. Personally i prefer oscam but the lines i use are n-line in CWS format.


    My question is can I use a line like this -----> CWS = thisismyserver 15221 test test 01 02 03 04 05 06 07 08 09 10 11 12 13 14 in Oscam to make the channels clear. If I can then how can I do this and also add CWS_MULTIPLE = thisismyserver 15221 test test 01 02 03 04 05 06 07 08 09 10 11 12 13 14 in Oscam IF NEEDED. Thanks in advance.

    Nlines and Clines can be converted to work in oscam.server as client, info is on here.


    And no, it is not added like this.


    CWS_MULTIPLE = thisismyserver 15221 test test 01 02 03 04 05 06 07 08 09 10 11 12 13 14

    Hi guys.


    Sorry to be asking this if you can help Please.


    What i can not seem to do is get my mgcamd server to send a reader to oscam, above these settings are for sending a line to mgcamd from oscam, I ask can i send a line from mgcamd to oscam and how please. and in which file in mgcamd do i put the user please.


    regards Talks.

    Quote from master G

    Mgcamd doesn't work as a server, it's a client only emulator.

    Thanks for a fast answer master G, so how would my local card that is in oscam,, update if mgcamd is a client to oscam please i am trying to see where i am going wrong here. maybe i am going wrong somewhere because looking at the post above your showing a reader in oscam that i assume is from the mgcamd, but where is the corresponding line to the reader go in the mgcamd files?


    thanks.


    regards Talks.

    Edited 2 times, last by Talks ().

    Quote from master G

    The mgcamd client sends emm's to oscam that will update entitlements.
    Are you using a Linux pc or receiver as server ?

    thanks again master G,


    I am using a vu solo2 as the oscam, and a dm800se as mgcamd so two dif ip's set to each stb.


    192,xxxxx 100 < dm800 mgcamd
    192,xxxxx 106 < vusolo oscam


    regards Talks.

    Edited once, last by Talks ().

    • Official Post

    The attached configs will update your card without the need for mgcamd.. If you also want to use mgcamd add [newcamd] to oscam.conf, setup an [account] for mgcamd, then add CWS line to the dm800se client..


    oscam.conf

    Code
    [newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000


    oscam.user

    Code
    [account]
user = mgcamd
pass = password
group = 1
au = SKYUK


    newcamd.list

    Code
    CWS = 192.xxxxx.100 10000 mgcamd password 0102030405060708091011121314
    Quote from master G

    An n-line in CWS format still uses newcamd protocol, add a remote newcamd reader in oscam server like this;


    Code
    [reader]
label     = my cws line converted
protocol  = newcamd
key       = 0102030405060708091011121314
device    = thisismyserver,15221
user      = test
password  = test
group     = 2




    THANK YOU!


    That settings work perfect with mgcamd, but with litle diferece:

    Code
    [reader]
label     = thisismyserver,converted
protocol  = newcamd
key       = 0102030405060708091011121314
device    = thisismyserver,15221
user      = test
password  = test
group     = 1





Your resource for OSCam softcam

Find configs, downloads, tutorials, and support for setting up and optimizing this open-source card server with wide protocol compatibility. Master the versatile OSCam softcam. Access support, configs, tutorials, and downloads for open-source card sharing and multi-protocol server management.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login