need oscam/cccam setup for BT Sports $$$.uk

Harley you have that part in post 18 bud

Indeed but I still cannot get it to work so I can see the entitlements. The webif is already on my box.

I have tried to use the configs set out in a file posted here further back but when I did put this on my box, it stopped clearing the channels. A few of them had the oscam label appear on screen as if it was opening the channel but no luck.

Some channels were ignored completely. So I had to put the cccam.cfg file back to how it was and then it started working again.

this does not make sense. Can anyone else help? Without that I still cannot see the entitlements.

Thanks in advance.

Just to also say that the N line in the cccam.cfg for the configs in the ** S**** file says 10001, not 16001. I wonder is this why it will not work. Thanks.

you are getting mixed up with the ports 16001 will be your webif port for cccam the other is for the nline this connects oscam to cccam ,oscam is running the card cccam is your server

Thanks. So why is port 16002 not working which is where the oscam port should be in my configs? I just get "Unable to connect. Can't Establish a connection to the server at ...:16002".

So if Oscam is running the card, why can't I get this on my PC?

Quote from harley22

Thanks. So why is port 16002 not working which is where the oscam port should be in my configs? I just get "Unable to connect. Can't Establish a connection to the server at ...:16002".

So if Oscam is running the card, why can't I get this on my PC?

your post 18 is wrong
[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

look at the bottom line of this bud

thanks. So is it just this bit

httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

I seem to have missed out 127,0,0,1,

Would I be right? If I add in httpallowed = 127,0,0,1, prior to 192.168,0,0-192.168.255,255

will it work then? Does the port HAVE TO BE 8888? I have never had that working except when someone did it for me, but as soon as I rebooted my box it disappeared.

And, do I need admin for the httpuser and password?

Thanks.

Quote from harley22

thanks. So is it just this bit

httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

I seem to have missed out 127,0,0,1,

Would I be right? If I add in httpallowed = 127,0,0,1, prior to 192.168,0,0-192.168.255,255

will it work then? Does the port HAVE TO BE 8888? I have never had that working except when someone did it for me, but as soon as I rebooted my box it disappeared.

And, do I need admin for the httpuser and password?

Thanks.

Display More

port can be what you want the info there should be good enough with out degug etc use that and make your port to what you like

What is the difference if you put debug = 255 underneath? And, do I need a username and password?

or just start again and uninstall both then download it of tspanel in the linux support section, add your n-line into cccam as per tutorial and insert your white card. it will work and your webif will work on those ports

I have added the 127,0,0,1 into httpallowed now but my n: line - this must vary - what would that be? Thanks.

I will by the way, restart my box and see what happens? I only have an F: line in cccam at present. I also have a refee4cne to cccam 2.1.4 in .conf, do I need to change this to 2.1.3. Thanks.

Despite thata no luck I'm afraid. The cccam 2.1.3 server is working but not oscam server via my browser.

I have now put it back to 8888 for now.

this is really driving my mad - this should be easy but it is anything but.

If someone can help me with TeamViewer, please can you do so. Thanks.

OK it would appear that Oscam 1.00#6829 does NOT work with the cccam.cfg CONFIGURATION FOR ** s**** as described earlier.

This does not make sense to me. Adding 127,0,0,1 to the hhttpallowed did nothing for me.

My cardreader is acting just like a non-linux box and I am getting very frustrated about it.

I cannot uninstall anything on the box - it is not possible as far as I know. Nor can I reflash the box as I am not sure then if it will work afterwards.

Also I have never managed to get Oscam 1.20 working. Could this be a factor? Not sure if 1.20 is compatible with *** UK.

Please advise. Thanks.

Quote

This does not make sense to me. Adding 127,0,0,1 to the hhttpallowed did nothing for me.

it is not 127,0,0,1

its

127.0.0.1

This is localhost

Quote

Also I have never managed to get Oscam 1.20 working. Could this be a factor? Not sure if 1.20 is compatible with *** UK.

Please advise. Thanks.

Oscam 1.20 works very well with slyUK

What server are you using? PC or Box?

Also m8, calm down and relax before you burst a blood vessel..

If you cant uninstall anything maybe its time you gave your box a reflash. i have not read the full thread so tell me what you have mate.

box model
current image

I have now changed the localhost to 127.0.0.1. I did have ,s instead of full stops - will have to reboot first.

My box is TM Twin OE with Enigma 2 4D image.

As I say it's al working but not reading entitlements.

After all that, localhost does not work for me. 127.0.0.1 will not connect.

I cannot even get into thaton my browser.

Harley it will work i just think your needing to pay more attention to what your reading you have likely got ,.and spacings all wrong everywhere you have changed settings

Quote

After all that, localhost does not work for me. 127.0.0.1 will not connect.

I cannot even get into thaton my browser.

This is not an address to access from your browser, this just means that connections to webif from local host will be allowed.

I think the best thing to do is post your full configs and we will correct/modify where needed.

To access your webif from the browser, you use this:

192.168.1.***:8888

where...

"IP of server":"oscam webif port no"

The IP of server will be the local Static IP address of the device you have oscam installed on
for example... 192.168.1.100

The port number will be the port number you have set in your oscam.conf

[webif]
httpport = 8888