Help needed with getting Mgcamd running on AR-P Enigma2 image

Hi,
I am accesing someone elses cam server from my enigma2 golden media box and I am using oscam. but it stutters and the cam server guy says it because I should be using Mgcamd. I got the right Mgcamd files and edited newcamd.list with my details. I then select Mgcamd_138 in my softcam manager but nothing starts. I can go back to oscam and oscam starts, but due to the stutter is not much use.
I am sure the files are in the right directory and look ok but can't figure out why it's not working.

so any advice offered is appreciated.

Thanks but this was already there and still not starting. Do I need to remove all the Oscam files first?

here are some of the details on my setup, in case this helps:
Location of cam protocol
bf943cf92665.png

Location of cam files (Both these locations are listed correctly in my softcam manager.)
0ef5783b6d48b500a590ba3.png

Newcamd.list

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = <server> 12112 <login> <password> 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan

Mg_cfg

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 02 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 192.168.1.8 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 04 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

sorry, let me try to clear that up.

I can use oscam protocol to connect to a 3rd partys cam but it stutters , the 3rd party said I should be using mgcamd instead as I am a client , not a server. However mgcamd does not start for me.

changed the cam to mgcamd_1.35 but still nothing. 1 question, is copying the mgcamd cam file into the directory enough, or do I need to install anything (like a package)?

I switched back to spark (instead of eigma2) to see if I could get it working, but I have no idea how to run mgcamd on spark. Ayone have a dummies guide to ruing mgcamd on spark?

Still not working after I changed the G: { 01 } to G: { 33 } in my mg_cfg file.

will do, got it worknng on spark after a reboot. and now re-imaged enigma2 , but still no joy. must be the mgcamd cam I am using is wrong. do you have aink to the one you are using.

I tried these 2 : MGcamd 1.38.c Stable-mips E2 by Leo & e2-mipsel-mgcamd_1.35_100122

Yes already have the server and login details in the file, I just took them out in my post for security reasons. CWS = <server> 12112 <login> <password> 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan