Dreambox 500 hd and 4 disecq

There are 7 replies in this Thread which was already clicked 2,435 times. The last Post () by bagnoreggio.

  • Hallo everyone
    I have a DM 500 HD with 4 Disecq switch and I selected 1.0 in Disecq mode; the setting is working with Ipbox 900hd but when I switched the same setting to DM 500 HD (with any image) it is not working: every time when I switched channel of 4th satellite to another satellite - TUNE FAILED message appears. I need to go to Tuner setting and select the required satellite and click OK and than channel appears; only the 4th satellite always is working.
    Who can help me?

  • Stands a chance that the reciver doesn't like the DISEqC switch. Its not that uncommon.


    I have a cheapo Konig switch which works fine with my daughters nBox, but my Gigablues and my DM800Se won't work with it. You may find that to get it to work that you may have to change the DISEqC switch to a different brand.


    Nano

  • Configuration Mode = advanced
    *Satellite = Hotbird 13E (any satellite name)
    Voltage mode = Polarization
    Tone mode = Band
    *LNB = LNB 8 (change 1-8)
    DiSEqC mode = 1.1
    Tone-burst = None
    Committed DiSEqC command = none
    Fast DiSEqC = no
    Sequence repeat = no
    Command order = uncommitted, committed, toneburst
    *Umcommitted DiSEqC command = Input 8 (change 1-8 according to LNB above)
    DiSEqC repeats = None
    LOF = Universal LNB
    Increased voltage = yes
    Polarity = Auto


    *Only change these settings

    110cm Triax Dish multi arm 13,16,19, 23, 28 east fixed 90cm thor

  • you then need to change to your next sat and increase the number to suit the input on the switch and so on up to your 4, i have this setup on my dm800 and then when i changed to the vu solo2
    and it definitely works, if your unsure about the settings save them after you input the details for each lnb but you shouldnt have to.

    110cm Triax Dish multi arm 13,16,19, 23, 28 east fixed 90cm thor

  • Well, Before three months ago the swicht worked good with simple configuration diseqc a-b-c-d; Now I thing DM corrupt.


    Anyway I tried the settings below:


    Configuration Mode = advanced
    Satellite = Astra1 (19,2E)
    LNB = LNB 1
    Priority = Auto
    LOF = Universal LNB
    Voltage mode = Polarization
    Tone mode = Band
    Increased voltage = Yes
    DiSEqC mode = 1.1
    Toneburst = None
    Committed DiSEqC command = None
    Fast DiSEqC = no
    Sequence repeat = no
    Command order = uncommitted, committed, toneburst
    Umcommitted DiSEqC command = Input 1
    DiSEqC repeats = None


    For other sat I have changed:
    Satellite = Hotbird (13,0E)
    LNB = LNB 2
    Umcommitted DiSEqC command = Input 2


    Satellite = Eutelsat 7A (7,0E)
    LNB = LNB 3
    Umcommitted DiSEqC command = Input 3


    Satellite = Eutelsat 9A (9,0E)
    LNB = LNB 4
    Umcommitted DiSEqC command = Input 4


    Thank you and sorry for my bad english

  • Good news


    I fixed my diseqc problem in this simple mode:
    sat 7 est > in 1 (a) diseqc
    sat 9 est > in 2 (b) diseqc
    sat 13 est > in 3 (c) diseqc
    sat 19 est > in 4 (d) diseqc
    I don’t know why with this satellite order the switch is working good, maybe it depends on satellites.xml file

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!