Error activating card

Hello

Running 1.20-unstable_svn build r9202 on a Raspberry installed after the guide here. Card Reader: Infinity USB unlimited

2 Cards works in original box but get the following error when I try to Raspberry r:

Error activating card.

Any

[global]
logfile = /usr/local/etc/log/oscam.log
disableuserfile = 0
nice = -1
maxlogsize = 200
preferlocalcards = 1
usrfile = /usr/local/etc/log/oscamuser.log
emmlogdir = /usr/local/etc/log
lb_savepath = /usr/local/etc/log
lb_nbest_percaid = 04:1

[cache]

[cccam]
port = xxx
nodeid = 274EEF361xxxxx
version = 2.1.4
reshare = 1
forward_origin_card = 1

[newcamd]
port = 9999@093E:000000
key = 0102030405060708091011xxxxxxx
keepalive = 1
mgclient = 1

enabled = 1
au = 1
user = dvbapi_cccam-3
boxtype = pc

[monitor]
port = 988
aulow = 120
monlevel = 0
hideclient_to = 0

[webif]
httpport = xxx
httpuser = oscam
httppwd xxxxx
httprefresh = 10
httpallowed = 127.0.0.1,255.255.255.255,255.255.255.255,192.168.0.0-192.168.255.255
aulow = 120
hideclient_to = 0

reader]
label = V*****
enable = 1
protocol = mouse
device = /dev/ttyUSB0
autospeed = 0
caid = 093E
boxid = xxxxxxx
ins7e11 = 15
detect = cd
ident = 093E:000000
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-g = 1
audisabled = 1
auprovid = 00093E
2014/01/16 18:38:02 0 s >> OSCam << cardserver started, version 1.20-unstable_svn, build r9202 (arm-linux-gnueabihf)
2014/01/16 18:38:02 0 s creating pidfile /tmp/.oscam/oscam.pid with pid 2343
2014/01/16 18:38:02 0 s couldn't open statistics file: /usr/local/etc/log/oscamuser.log
2014/01/16 18:38:02 0 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2014/01/16 18:38:02 0 s signal handling initialized
2014/01/16 18:38:02 0 s monitor: initialized (fd=4, port=988)
2014/01/16 18:38:02 0 s newcamd: initialized (fd=5, port=9999)
2014/01/16 18:38:02 0 s -> CAID: 093E PROVID: 000000
2014/01/16 18:38:02 0 s cccam: initialized (fd=6, port=1xxx)
2014/01/16 18:38:02 0 s Viasat [mouse] creating thread for device /dev/ttyUSB0
2014/01/16 18:38:02 0 s loadbalancer: can't read from file /usr/local/etc/log
2014/01/16 18:38:02 0 s waiting for local card init
2014/01/16 18:38:02 10399D0 h webif: decompressed 55194 bytes back into 163800 bytes
2014/01/16 18:38:02 10399D0 h HTTP Server running. ip=0.0.0.0 port=xxx
2014/01/16 18:38:02 10378C0 r Viasat [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=357, cardmhz=357)
2014/01/16 18:38:04 0 s init for all local cards done
2014/01/16 18:38:04 0 s anti cascading disabled
2014/01/16 18:40:51 10378C0 r Viasat [mouse] card detected
2014/01/16 18:40:54 10378C0 r Viasat [mouse] Error activating card.
2014/01/16 18:41:03 0 --- Skipped 2 duplicated log lines ---
2014/01/16 18:41:03 10378C0 r Viasat [mouse] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2014/01/16 18:41:03 10378C0 r Viasat [mouse] card initializing error

Quote from anniman

you need to add in to the reader section
mhz = 450
cardmhz = 2700

Thanks, it works unfortunately. When I insert the 2 lines can Oscam not boot.

Trying again and returns

you need to add in to the reader section
mhz = 450
cardmhz = 2700
Thanks, it works unfortunately. When I insert the 2 lines can Oscam not boot.

Unfortunately, when I insert the 2 lines stop oscam and will not start on reboot. Now I have tried 3 times and have to put a new image on the SD card in Raspi because it is faster than reinstalling.

Run lsusb in telnet to get the correct device output for the infinity usb smart, then edit the [reader] in oscam.server;

(you should get an output like this: Bus 001 Device 006: ID 104f:0006 WB Electronics Infinity Smart)

Code:
[reader]
label = VIASAT
enable = 1
protocol = smartreader
device = Infinity;001:006
caid = 093E
boxid = xxxxxxx
ins7e11 = 15
detect = cd
ident = 093E:000000
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-g = 1
audisabled = 1
auprovid = 093E
It is tried and gives far more errors than when the system is run as described in the files with.
The card reader is not activated, and it reports an error in the address even though I write it obtained with lsubl
When I run the attached setup activates the reader and is green.

No, unfortunately. It does not work, is back at startup as described in the first post.
How do I find an older version? and it is just to change the file in the "bin"?

Hello again

As mentioned, it does not work and I have no idea why. It does look, unfortunately, does not seem there are others who can solve the problem, or?

Alternatively, I have to buy another reader?